Manuals / Dell / Computer Equipment / Server

Dell E600I manual SFM Front Panel and LEDs, 2defines the SFM front panel and LED displays

Models: E600I

1 76

Download 76 pages 63.1 Kb

Page 35

SFM Front Panel and LEDs

Table 7-2defines the SFM front panel and LED displays.

Table 7-2. SFM Front Panel and LED Descriptions

LED	Description

Active	Green: active and passing traffic
	Unlit: in standby mode

CC-E-SFM3

Active

Status	Flashing Green: booting
	Green: operational
	Flashing Amber: communication failure
	Amber: fault detected
	Unlit: no power

Status

Switch Fabric

Assy

Serial

Installing RPMs, Line Cards, and SFMs 35

Image 35

Dell E600I SFM Front Panel and LEDs, 2defines the SFM front panel and LED displays, SFM Front Panel and LED Descriptions

Contents

E600i TeraScale Installation Guide Page Contents Powering Up System Boot W . d e l l . c o m s u p p o r t . d e l l . c o m Contents About This Guide Information Symbols and Warnings1describes symbols contained in this guide Information SymbolsRelease Notes for the E-Series Related PublicationsEquipment Rack and Cabinet Requirements Site PreparationSite Selection Storage Requirements Power Requirements2500W AC Power Requirements DC Power RequirementsOperating Overview E600i SystemE600i Chassis Rear View E600i Chassis Front View with AC Power SuppliesE600i Hardware Component Operating Requirements Summary E600i System Installation ProcessPage Unpacking the E600i System Installing the ChassisInstalling the Equipment Rack Shelf Bar Standard Front Chassis Rack Mounting To install a equipment rack shelf barTo install the chassis into a prepared rack Installing the Chassis into an Equipment CabinetPage Fan Tray Installing the Fan TrayFan Speed Fan Speed and TemperatureMinimum Power Supply Requirements Power SupplyAC Power Supply Unit AC Power Supply UnitsTo install an AC power supply unit Power Cord RequirementsInstall the AC Power Supply Units To remove an AC power supply unit Remove the AC Power SupplyTo install a DC PEM DC Power Entry ModulesCable and Connector Requirements Install the DC PEMsReplace the DC PEM Removing the DC PEM Safety CoverTo remove a PEM Page RPMs Installing RPMs, Line Cards, and SFMsUnpacking Line Cards and RPMsBlank Panels Preparing and Installing the RPMs and Line CardsTo install line cards and RPMs Line CardsInstalling RPM into the E600i RPM LEDs Installing a Second RPMRPM Label and LEDs Line Card LEDs Installing Switch Fabric Modules SFMsInstalling SFMs SFM Front Panel and LED Descriptions SFM Front Panel and LEDs2defines the SFM front panel and LED displays Page RPM Ports Connecting the Console and Auxiliary PortsRPM Ports and Cables Auxiliary Port RJ-45 Pin Assignments Cable and Adapter Pin AssignmentsConsole Port RJ-45 Pin Assignments Pin Assignments Between E600i Console and DB-25 Adapter Accessing the Console with a DB-9 AdapterAccessing the Console with a DB-25 Adapter 100 Ethernet Management Port LEDs Accessing the 10/100 Ethernet Management PortAccessing the Auxiliary Port by Modem RJ-45 to DB-25 Adapter Pin Modem AssignmentsPreparation Powering UpSupplying Power To supply power to the E600i systemBooting from the Bootuser Prompt Booting to the CLI PromptRemoving and Replacing the Fan Tray Removing and Replacing PartsReplacing 2500W AC Power Supply Removing and Replacing Power ModulesReplacing DC PEMs Removing the Power CordDC PEM Label Removing and Replacing RPMs, Line Cards, or SFMsNo linecard number To remove and install an SFMReplacing the E600i Air Filter Removing and Replacing the Air FilterTo remove and replace the air filter Page Removing the External Flash Memory Card Using a Flash Memory CardExternal Flash Memory Card Overview Inserting the External Flash Memory CardDisplaying Files Stored on the External Flash Formatting an External Flash CardCopying Files to the External Flash Dir Command Example Page Booting from the Bootuser Prompt System BootE600i System Boot Process Help To configure the chassis from the Bootuser promptUse the boot change command to edit appropriate fields Show default-gateway default-gateway ip-address Force10 Page Table B-1. Alarm Events and Reporting AlarmsSFMs and Alarms AC Power Supplies and AlarmsAlarms Alarms W . d e l l . c o m s u p p o r t . d e l l . c o m This appendix contains the following major sections System SpecificationsChassis Physical Design Environmental AC Power Supply Unit RequirementsDC Power Entry Module Requirement Agency Compliance SFM and RPM Power RequirementsJapan Vcci Compliance for Class a Equipment Product Recycling and Disposal Safety Standards and Compliance Agency CertificationsElectromagnetic Compatibility EMC Figure C-1. The European Weee symbol This appendix contains these major sections Accessing iSupport ServicesTechnical Support ISupport WebsiteRequest tab Contacting the Technical Assistance CenterTo request replacement hardware, follow these steps Requesting a Hardware ReplacementPage Page W. d e l l . c o m s u p p o r t . d e l l . c o m