Dell E600I - page 58

58 | System Boot

www.dell.com | support.dell.com

6interface management port

config 100m

interface management port

config 10m

interface management port

config auto-negotiate

interface management port

config no auto-negotiate

interface management port

config full-duplex

interface management port

config half-duplex

interface management port

config show

• (OPTIONAL) Use these commands to set the speed and duplex settings for the

Management interface.The default setting is full-duplex and auto-negotiation.

• Use the interface management port config show command to view the

Management interface’s physical settings.

7show interface

management ethernet

interface management

ethernet ip address ip-

address ip-address-mask

• Use the show interface management ethernet command to display the IP

address and network mask of the management Ethernet port.

• If the show command output does not display configured IP address information,

use the interface management ethernet ip address ip-address ip-address-

mask command to set the IP address of the Management Ethernet port for

network (ftp/tftp) operating system boot.

8show default-gateway

default-gateway ip-address

(OPTIONAL) Use the show default-gateway command to view gateway

information.

If your server is on the same subnet, you do not need to configure a gateway

parameter.

If your server is not on the same subnet, use the default-gateway ip-address

command to set the gateway IP address.

BOOT_USER # show interface management ethernet

No IP address set for interface management ethernet 0/0!

BOOT_USER # interface management ethernet ip address 1.2.3.4 255.255.0.0

Management ethernet 0/0 IP address: 1.2.3.4 255.255.0.0

BOOT_USER # show interface management ethernet

Management ethernet IP address: 1.2.3.4:ffffff00

BOOT_USER #

BOOT_USER # show default-gateway

No gateway IP address specified!

BOOT_USER # default-gateway ip 1.2.3.5

Gateway IP address 1.2.3.5

BOOT_USER # show default-gateway

Gateway IP address: 1.2.3.5

BOOT_USER #

Contents

Main Notes, Cautions, and Warnings followed. Contents 7 Installing RPMs, Line Cards, and SFMs 8 RPM Ports and Cables 9 Powering Up 10 Removing and Replacing Parts 11 Using a Flash Memory Card A System Boot B Alarms C System Specifications D Technical Support Page About This Guide Information Symbols and Warnings Related Publications Site Preparation Site Selection Equipment Rack and Cabinet Requirements Power Requirements Storage Requirements The E600i System Operating Overview Page E600i System Installation Process Page Installing the Chassis Unpacking the E600i System Installing the Equipment Rack Shelf Bar Standard Front Chassis Rack Mounting Installing the Chassis into an Equipment Cabinet Page Installing the Fan Tray Page Power Supply AC Power Supply Units Page Remove the AC Power Supply To remove an AC power supply unit: Cord Retainer Power Cord Thumb Screw DC Power Entry Modules Page To remove a PEM: Page Installing RPMs, Line Cards, and SFMs Unpacking Line Cards and RPMs Preparing and Installing the RPMs and Line Cards To install line cards and RPMs: RPM Label and LEDs Line Card LEDs You must install SFMs starting on the left (slots 3 or 0) moving to the right (slots 2 or 4). Installing Switch Fabric Modules (SFMs) Page SFM Front Panel and LEDs Table 7-2 defines the SFM front panel and LED displays. Page RPM Ports and Cables RPM Ports Cable and Adapter Pin Assignments Page Accessing the 10/100 Ethernet Management Port Powering Up Preparation Supplying Power Booting to the CLI Prompt Removing and Replacing Parts Removing and Replacing the Fan Tray Removing and Replacing Power Modules Page To remove a PEM: Removing and Replacing RPMs, Line Cards, or SFMs for more details. To remove and replace RPMs and line cards: To remove and install an SFM: Removing and Replacing the Air Filter Page Page Using a Flash Memory Card External Flash Memory Card Overview Formatting an External Flash Card Copying Files to the External Flash Displaying Files Stored on the External Flash Page Page A System Boot The E600i System Boot Process Booting from the BOOT_USER Prompt To configure the chassis from the BOOT_USER prompt: Page Page Page Page B Alarms AC Power Supplies and Alarms SFMs and Alarms Page Page C System Specifications Chassis Physical Design Environmental AC Power Supply Unit Requirements DC Power Entry Module Requirement SFM and RPM Power Requirements Agency Compliance The E600i is designed to comply with the following safety and agency requirements. which case, the user may be required to take adequate measures. SFM 60W (210 BTU/hour) RPM 150W (510 BTU/hour) Page Page Page D Technical Support The iSupport Website Contacting the Technical Assistance Center , below, for more. Contacting the Technical Assistance Center Requesting a Hardware Replacement To request replacement hardware, follow these steps: