Dell E600I C

System Specifications | 65

C

System Specifications

This appendix contains the following major sections:

•Chassis Physical Design

•AC Power Supply Unit Requirements

•DC Power Entry Module Requirement

•Agency Compliance

Chassis Physical Design

Parameter Specifications

Height 28 inches (71.1 cm)

Width 17.4 inches (44.2 cm)

Depth (without cable management system) 21.5 inches (54.6 cm)

Chassis weight with factory-installed components

(backplane and air filter) 81 pounds (36.7 kg)

Weight fully loaded (backplane, air filter, fan tray,

SFMs, RPMs, and 7 line cards) 242 pounds (109.8 kg)

Mounting Factory-installed rack mount brackets for front, center, or

rear mounting in a standard 19-inch rack.

Optional brackets for mounting in a standard 23-inch rack or

cabinet.

Rack clearance required Front: 18-inches

Rear: 20-inches

Maximum Thermal output:

NOTE: Thermal output is directly proportional

to system configuration and number of line cards.

• Maximum for fully loaded chassis 120 VAC powered: 4705W (16,065 BTU/hour)

200/240 VAC powered: 4250W (14,500 BTU/hour)

DC powered: 2800W (9600 BTU/hour)

Contents

Main Notes, Cautions, and Warnings followed. Contents 7 Installing RPMs, Line Cards, and SFMs 8 RPM Ports and Cables 9 Powering Up 10 Removing and Replacing Parts 11 Using a Flash Memory Card A System Boot B Alarms C System Specifications D Technical Support Page About This Guide Information Symbols and Warnings Related Publications Site Preparation Site Selection Equipment Rack and Cabinet Requirements Power Requirements Storage Requirements The E600i System Operating Overview Page E600i System Installation Process Page Installing the Chassis Unpacking the E600i System Installing the Equipment Rack Shelf Bar Standard Front Chassis Rack Mounting Installing the Chassis into an Equipment Cabinet Page Installing the Fan Tray Page Power Supply AC Power Supply Units Page Remove the AC Power Supply To remove an AC power supply unit: Cord Retainer Power Cord Thumb Screw DC Power Entry Modules Page To remove a PEM: Page Installing RPMs, Line Cards, and SFMs Unpacking Line Cards and RPMs Preparing and Installing the RPMs and Line Cards To install line cards and RPMs: RPM Label and LEDs Line Card LEDs You must install SFMs starting on the left (slots 3 or 0) moving to the right (slots 2 or 4). Installing Switch Fabric Modules (SFMs) Page SFM Front Panel and LEDs Table 7-2 defines the SFM front panel and LED displays. Page RPM Ports and Cables RPM Ports Cable and Adapter Pin Assignments Page Accessing the 10/100 Ethernet Management Port Powering Up Preparation Supplying Power Booting to the CLI Prompt Removing and Replacing Parts Removing and Replacing the Fan Tray Removing and Replacing Power Modules Page To remove a PEM: Removing and Replacing RPMs, Line Cards, or SFMs for more details. To remove and replace RPMs and line cards: To remove and install an SFM: Removing and Replacing the Air Filter Page Page Using a Flash Memory Card External Flash Memory Card Overview Formatting an External Flash Card Copying Files to the External Flash Displaying Files Stored on the External Flash Page Page A System Boot The E600i System Boot Process Booting from the BOOT_USER Prompt To configure the chassis from the BOOT_USER prompt: Page Page Page Page B Alarms AC Power Supplies and Alarms SFMs and Alarms Page Page C System Specifications Chassis Physical Design Environmental AC Power Supply Unit Requirements DC Power Entry Module Requirement SFM and RPM Power Requirements Agency Compliance The E600i is designed to comply with the following safety and agency requirements. which case, the user may be required to take adequate measures. SFM 60W (210 BTU/hour) RPM 150W (510 BTU/hour) Page Page Page D Technical Support The iSupport Website Contacting the Technical Assistance Center , below, for more. Contacting the Technical Assistance Center Requesting a Hardware Replacement To request replacement hardware, follow these steps: