Dell E600I - page 59

System Boot | 59

Refer to the FTOS Command Line Interface Reference for CLI details, and to the FTOS Configuration Guide for configuration procedures.

9dir flash:

dir slot0:

Use the dir flash: command to list files stored on the internal flash device.

Use the dir slot0: command to list files stored on the external flash device.

10 reload Reload software.

The autoboot program initializes and displays self-test results on the console screen.

NOTE: Do not press break control sequence at any time during the boot/reboot

process. Doing so causes the boot process to terminate.

11 Force10> When the reboot completes, the CLI defaults to the EXEC mode.

BOOT_USER # dir flash:

Displaying files in flash:

size date time name

-------- ------ ------ --------

11187685 FEB-15-2006 05:37:58 E600i-.bin

11031398 FEB-23-2006 22:42:46 E600i-3.bin

9280984 FEB-17-2006 21:02:36 E600i-2.bin

10778521 FEB-18-2006 22:53:26 E600i-3.1.bin

1787 FEB-23-2006 22:42:46 startup-config

BOOT_USER #

Contents

Main Notes, Cautions, and Warnings followed. Contents 7 Installing RPMs, Line Cards, and SFMs 8 RPM Ports and Cables 9 Powering Up 10 Removing and Replacing Parts 11 Using a Flash Memory Card A System Boot B Alarms C System Specifications D Technical Support Page About This Guide Information Symbols and Warnings Related Publications Site Preparation Site Selection Equipment Rack and Cabinet Requirements Power Requirements Storage Requirements The E600i System Operating Overview Page E600i System Installation Process Page Installing the Chassis Unpacking the E600i System Installing the Equipment Rack Shelf Bar Standard Front Chassis Rack Mounting Installing the Chassis into an Equipment Cabinet Page Installing the Fan Tray Page Power Supply AC Power Supply Units Page Remove the AC Power Supply To remove an AC power supply unit: Cord Retainer Power Cord Thumb Screw DC Power Entry Modules Page To remove a PEM: Page Installing RPMs, Line Cards, and SFMs Unpacking Line Cards and RPMs Preparing and Installing the RPMs and Line Cards To install line cards and RPMs: RPM Label and LEDs Line Card LEDs You must install SFMs starting on the left (slots 3 or 0) moving to the right (slots 2 or 4). Installing Switch Fabric Modules (SFMs) Page SFM Front Panel and LEDs Table 7-2 defines the SFM front panel and LED displays. Page RPM Ports and Cables RPM Ports Cable and Adapter Pin Assignments Page Accessing the 10/100 Ethernet Management Port Powering Up Preparation Supplying Power Booting to the CLI Prompt Removing and Replacing Parts Removing and Replacing the Fan Tray Removing and Replacing Power Modules Page To remove a PEM: Removing and Replacing RPMs, Line Cards, or SFMs for more details. To remove and replace RPMs and line cards: To remove and install an SFM: Removing and Replacing the Air Filter Page Page Using a Flash Memory Card External Flash Memory Card Overview Formatting an External Flash Card Copying Files to the External Flash Displaying Files Stored on the External Flash Page Page A System Boot The E600i System Boot Process Booting from the BOOT_USER Prompt To configure the chassis from the BOOT_USER prompt: Page Page Page Page B Alarms AC Power Supplies and Alarms SFMs and Alarms Page Page C System Specifications Chassis Physical Design Environmental AC Power Supply Unit Requirements DC Power Entry Module Requirement SFM and RPM Power Requirements Agency Compliance The E600i is designed to comply with the following safety and agency requirements. which case, the user may be required to take adequate measures. SFM 60W (210 BTU/hour) RPM 150W (510 BTU/hour) Page Page Page D Technical Support The iSupport Website Contacting the Technical Assistance Center , below, for more. Contacting the Technical Assistance Center Requesting a Hardware Replacement To request replacement hardware, follow these steps: