Denon ADV-700 manual Preset memory, Audio Component, Combinations of Personal System Codes

(3)Preset memory

[1]Audio Component

•The signals of your other Denon products can be stored in the included remote control unit’s preset memory to operate either the CDR, MD or TAPE function.

Operation is not possible for some models.

	CH			1
ON	1	2	3
POWER	CH		VCR
OFF	4	5	6
VCR POWER	CH		VOL
CLEAR	7	8	9	TV
TV POWER	CH	TV/VCR	SLEEP
CALL	+10	0
DISPLAY	RETURN	INPUT MODE SURROUND
MENU			FUNCTION

ENTER

MODE

VOLUME

BAND

			MUTE
CH		SHIFT
		NTSC/PAL	STATUS
TU		MEMO
SUB TITLE	AUDIO	ANGLE	TOP MENU
PROG/DIRECT	REPEAT A-B	REPEAT	RANDOM

CH.SELECT T.TONE SDB/TONE SURR.PARA

SETUP CDR/MD/TAPE TUNER/TV/VCR DVD

REMOCON MODE

1

1	While pressing the CDR/MD/TAPE remote control mode
	selector button, input the 3-digit number (“000”, “111” and
	“222”) corresponding to the device you want to preset (CDR,
	MD or TAPE), referring to the table below.
	• Release the CDR/MD/TAPE button after inputting three
	digits. This completes the presetting operation.

Table 1: Combinations of Personal System Codes

CDR/MD/TAPE

Input the 3-digit number while pressing CDR/MD/TAPE.

CDR	0	0	0
MD	1	1	1
TAPE	2	2	2

This is set to CDR by factory default.

NOTE:

•Only one device (CDR, MD or TAPE) can be stored in the preset memory.

ENGLISH

[2] TV

•Other makes of components can be operated by setting the preset memory for your make of TV.

This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the components as shown on the List of Preset Codes (attached sheet).

Operation is not possible for some models.

		CH
	ON	1	2	3
	POWER	CH			VCR
	OFF	4	5	6		1
	VCR POWER	CH	VOL
	CLEAR	7	8	9	TV
1	TV POWER	CH	TV/VCR	SLEEP
	CALL	+10	0
	DISPLAY	RETURN	INPUT MODE	SURROUND
	MENU			FUNCTION
		ENTER
	MODE
				VOLUME
	BAND
				MUTE
	CH		SHIFT
			NTSC/PAL	STATUS
	TU		MEMO
	SUB TITLE	AUDIO	ANGLE	TOP MENU
	PROG/DIRECT	REPEAT A-B	REPEAT	RANDOM
	CH.SELECT	T.TONE	SDB/TONE	SURR.PARA
	SETUP CDR/MD/TAPE TUNER/TV/VCR			DVD

REMOCON MODE

1

1	Press the CALL button while pressing the TUNER/TV/VCR
	remote control mode selector button, then input the three-
	digit number corresponding to the code of the manufacturer
	of the TV whose signals you want to store, referring to the
	included list of remote control unit codes.
	• Release the TUNER/TV/VCR button after inputting three
	digits. This completes the presetting operation.
	Example: To preset to “Hitachi 074”
	TUNER/TV/VCR
		Press the buttons below while pressing TUNER/TV/VCR.
	HITACHI		TV POWER	0	7	4
			CALL
	“074”

This is set to “Hitachi 074” by factory default.

NOTE:

•Preset codes set upon shipment from the factory and when reset.

19