Connections
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Balanced
Microphones
Getting
Refer to the Connection Diagram below.
1.Make certain AC power is off while making connections.
2.Quality cables make a big difference in fidelity and punch. Use
3.Do not use excessively long cables.
Be sure plugs and terminals are securely fastened. Loose connections cause hum, noise, or intermittence that could damage your speakers.
4.Connect all stereo input sources. Then connect any effects into the stereo Effect, if used. Connect your Microphone(s) and monitor headphones. Make sure all faders are at “zero” and the unit is off. Take care to connect only one cable at a time. pay attention to L and R position of terminals, on both the
5.Connect the stereo outputs to the power amplifier(s) and/or tape deck(s) and/or Solid State recorder(s) and/or CD recorder(s).
NOTE
•Always switch on your audio input sources such as CD players first, then your mixer, and finally any amplifiers.
•When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input units.
Preparations
Cables Used for Connections
Select the cables according to the equipment being connected.
| Audio cables |
| |
For RCA PINJACK |
|
| |
L |
|
| L |
R |
|
| R |
| RCA pin plug |
|
|
For SEND/RETURN |
|
| |
Unbalanced | Unbalanced | ||
1/4” TS | 1/4” TS | ||
For MIC |
|
|
|
Balanced |
|
| Balanced |
Sleeve=GND | 1=GND | 2=Hot | |
| |||
Ring=Cold |
| 3=Cold | |
Tip=Hot |
|
| |
|
|
| |
1/4” TRS |
| ||
For BALANCED MASTER OUT |
| ||
Balanced |
|
| Balanced |
2=Hot | 1=GND |
|
|
| 1/4” TRS |
|
|
Sleeve=GND | |||
3=Cold |
| Ring=Cold | |
Turntable | Turntable | XLR or |
|
| 1/4” TRS |
|
| balanced |
|
PUSH |
Mic USB Thumb Drive 
CD recorder or PC
Tape deck | Booth balanced/ | 1/4” TRS | |||||||
|
|
|
|
|
|
|
| power amplifier | balanced |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
USB B terminal | Main unbalanced |
| power amplifier |
Effects processor
Started Connections Basic Operations Effector Function Fader Start USB Utility Specifications
Tip=Hot |
Booth balanced/ power amplifier
ASIO Driver Application included.
Computer OS versions that can be connected to the
Sequencer
Troubleshooting
•Windows XP SP2, Vista, Mac OSX 10.4 or later Computers with other operating systems are not compatible with USB MIDI, so the computer may operate erratically after connected to the
•Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and / or other countries. MAC is either a registered trademark or trademark of Apple Incorporated in the United States and / or other countries.
NOTE
Keep volume at comfortable sound levels and avoid extended play at very high volume as it may cause temporary or permanent hearing loss.
7
