Getting Started Connections Basic Operations Effector Function Fader Start USB Utility Specifications
Q5Effect ON/OFF button
This sets the effects of EFX 1 or EFX 2 to ON or OFF.
Q6CROSSFADER
Controls the relative output level from the summed A and B Mixes. When the fader is at its far left, only the A Mix is heard from the Outputs. As the fader is moved toward the right, the amount of B Mix is increased and the amount of A Mix is decreased. When the fader is centered, equal amounts of A and B Mixes are routed to the Outputs. Fully right is all B Mix at the Outputs.
Q7Channel input fader (CH FADER)
Controls the level of the selected Input.
Q8HEADPHONE output jack
Accepts 1/4” stereo headphone plugs.
Q9HEADPHONE level control
Adjusts the volume for the headphones.
W0HEADPHONE PAN control
This is used to adjust the balance between the CUE sound and the master sound which are monitored using the headphones.
W1SPLIT CUE button
There are two headphone monitor modes.
Stereo mode (SPLIT CUE OFF):
The cue signals and master signals can be monitored in stereo.
SPLIT CUE mode:
The monaural cue signals are heard through the left channel of the headphones, and the monaural master signals through the right channel.
W2CROSSFADER CONTOUR control
Allows adjusting the “shape” of the Crossfader response from a gentle curve for smooth, long running fades, to the steep pitch required for top performance cut and scratch effects.
W6MIC SEND LEVEL control
This is used to adjust the level at which the mic signals are sent to the master output.
W7Mic EFX INS 1, 2 buttons
These buttons enable the various effects of the selected side, either EFX 1 or EFX 2, to be obtained for the mic input signals.
W8MIC EQ controls
Contour the frequency response of the Mic input
W9DUCKING ON/OFF button
•Use this to switch the Talk Over function ON and OFF. (ON/OFF is cyclic)
•When the button is lit, level of signals except Mics is attenuated.
* The ducking attenuation level can be adjusted in the “UTILITY” mode.
E0MIC1, MIC2 TRIM controls
Adjusts the level of the Main Mic input.
E1MIC1, 2 buttons
When the button’s LED is lighted, the mic signals take effect.
E2CD/PHONO line input selector buttons
These enable the line input of each channel to be selected as CD or PHONO.
CD:
Rear panel
PHONO:
Rear panel
E3SOURCE SEL
These enable any of six inputs to be selected for each of the channels. The same input can be selected for more than one channel. When DIGITAL is selected, the LED of the corresponding button lights up red; when USB is selected, it lights up blue.
E4MIDI layer selector buttons
When these buttons are set to ON, the controls of the selected channels function as MIDI controllers. Also, the EQ control rings light up blue.
E5Channel input LEVEL controls
These are used to adjust the levels of the selected inputs.
E6Channel isolator EQ controls (HI, MID, LOW)
These are used to change the frequency response of the selected inputs.
At the center position, the frequency response is flat.
At the
E7CH LEVEL meter
Displays the input level after adjusted with LEVEL E5and Source EQ E6controls.
E8Channel EFX SEND 1, 2 buttons
These buttons enable the various effects of the selected side, either EFX 1 or EFX 2, to be obtained for the channel audio signals. The same effect (EFX 1 or 2) can be selected for a multiple number of channels.
The LED of the EFX button for the side selected for each channel lights.
E9Channel CUE buttons
Pressing in any or all of CUE buttons routes the respective source to the headphone and meter cue sections. Pressing multiple buttons makes it possible to derive mixed sound from the selected sources.
*The SOLO mode with no signals mixed can also be selected as a preset.
R0CROSSFADER ASSIGN switches
A, B:
The channel source is assigned to A or B of the Crossfader.
R2L/CUE, R/PGM master level meter
One of two modes can be selected for display on this meter.
Split CUE OFF:
The master output audio level is displayed.
Split CUE ON:
The right channel master CUE (monaural) and
left channel CUE (monaural) audio levels are
displayed.
R3SIG/PK
This is the signal/peak meter for the mic input level.
Off:
No signals input (under
Green:
Signal input
Orange:
Suitable signal input level
Red:
Excessively high signal input level (above
Troubleshooting
W3CH FADER CONTOUR control
Adjusts the volume curve response of the channel fader.
W4CH FADER START switch
This function will start the performance of CD/ Media Player with Ch. Fader automatically is
ON/OFF.
W5CROSSFADER START switches
Use this to switch the Crossfader Start function
ON and OFF.
LINE1 
LINE2 
LINE3 
LINE4 
DIGITAL 
USB 
SOURCE SEL
CH1
SOURCE SEL
CH4
THRU:
Select when you don’t assign the channel source into the Crossfader.
R1MASTER BALANCE control
Adjusts the L/R balance of the MASTER output.
4
