Utility settings
Utility operations
In the Utility mode, the preset data inside the device can be set.
Press the | A/USB B button. The utility |
1 screen now appears. |
|
2and press the control to enter the selection.
When the selection is entered, the items and data are switched using the hierarchy shown in the table below.
To go back to the selection, press the BACK button. Operation then returns to the previous screen.Using the EFFECT SELECT2 control, select the item,
3button to turn off the Utility mode.
The data which has been set is now stored in the internal memory.In the Utility mode, press the
Preset Items and Data
Category |
| Item |
| Parameter | Value | Default | |
|
| Settings | |||||
|
|
|
|
|
|
| |
| 1 Master Setting | 1 MONO |
| ON / OFF | OFF | ||
|
|
| 1 | Ducking Level |
| ||
|
|
|
|
| 1 Hi | 1kHz to 4kHz | 2kHz |
| 2 | Mic Setting | 2 | Mic EQ | 2 Low | 500Hz to 2kHz | 1kHz |
|
|
|
|
| 3 Default |
| - |
|
|
| 3 | Mic to Booth/Rec |
| ON / OFF | OFF |
|
|
| 1 | X.Over Hi |
| 1kHz to 8kHz | 2kHz |
| 3 | Isolator EQ | 2 | X.Over Low |
| 100Hz to 800Hz | 350Hz |
|
|
| 3 | Default |
|
| - |
| 4 | Cue Setting | 1 | Cue Mode *¹ |
| CUE (Mix) / Solo | CUE (Mix) |
|
|
| 1 | EQ Hi |
| 0dB | |
| 5 Head Phones EQ | 2 EQ Low |
| 0dB | |||
|
|
| 3 | Default |
|
| - |
| 6 | EFX Send/Rtn | 1 | Unity Level Select |
| ||
1 Audio Setting |
|
|
|
| 1 USB1 / USB2 |
| Master |
|
| 1 | OutputSourceSelect | 2 USB3 / USB4 | Non, CH1, CH2, CH3, CH4, | Mic | |
|
|
| |||||
|
|
| 3 USB5 / USB6 | Master, Rec, Mic | CH2 | ||
|
|
|
|
| |||
| 7 | USB Audio Setting |
|
| 4 USB7 / USB8 |
| CH3 |
| 2 | Output Level VR |
| 0dB | |||
|
|
|
| ||||
|
|
| 3 | CH Input Level VR |
| ||
|
|
| 4 | Mas Input Level VR |
| ||
|
|
| 5 | Cue Input Level VR |
| ||
|
|
| 1 | Digital Output VR |
| 0dB | |
| 8 | Digital I/O Setting |
|
| CH1 | ||
| 2 | Digital Input Level | CH2 | ||||
|
|
| CH3 | ||||
|
|
|
|
| |||
|
|
|
|
| CH4 | ||
| 9 | 1 A Side Cut Position *² |
| 0.0mm | |||
| 2 | B Side Cut Position *² |
| 0.0mm | |||
|
|
|
| ||||
| 10 Beat Breaker Setting |
|
|
| 1 to 5 | 1 | |
| 1 | Sampling Frequency |
|
|
| 44.1KHz / 48KHz / 96KHz | 96kHz |
| 2 | Display Brightness |
|
|
| 1 to 40 | 27 |
2 System Setting | 3 | Display Backlight |
|
|
| 1 to 25 | 5 |
4 | Display Contrast |
|
|
| 1 to 16 | 15 | |
|
|
|
| ||||
| 5 PC/MAC*³ |
|
|
| PC Mode / MAC Mode | PC Mode | |
| 6 Version(SYS) |
|
|
| XXXX | - | |
| 1 MIDI INPUT CH |
|
|
| 1 to 16, OMNI | 1 | |
| 2 MIDI OUTPUT CH |
|
|
| 1 to 16 | 1 | |
3 MIDI Setting | 3 MIDI Output Enable | 1 | 5Pin |
| ON / OFF | ON | |
2 USB |
| ON / OFF | ON | ||||
|
|
|
| ||||
| 4 MIDI CLK | 1 | 5Pin |
| ON / OFF | ON | |
| 2 USB |
| ON / OFF | ON | |||
|
|
|
| ||||
4 Other Setting | 1 | Preset Export |
|
|
| Exit / Execute*4 | Exit |
2 |
|
|
| Exit / Execute*5 | Exit | ||
|
|
|
| ||||
5 Owner Setting | Display only |
|
|
|
|
| |
*1 When SOLO is selected as the CUE mode setting, only one of the two CUE buttons, whichever was pressed last, becomes operational. *2 The
*3 When the unit is connected to a computer which runs Windows XP, Vista or a similar operating system, select the PC Mode. When it is connected to a computer which runs Mac OSX or a similar operating system, select the MAC Mode.
*4 The settings for these Preset and the Owner mode settings can be stored on an external USB memory or other memory device.
*5 The settings for these Preset are set to the factory settings.
Getting Started Connections Basic Operations Effector Function Fader Start USB Utility Specifications Troubleshooting
17
