Optional Remote Operation, Thermostat Control Operation

OPERATING FIREPLACE (REMOTE-READY MODELS)

Optional Remote Operation

GWMT1 Wall Mounted Thermostat (Optional)

OPERATING FIREPLACE

Continued

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased sepa- rately (see Accessories, pages 38 and 39). Follow instructions included with the remote control.

Thermostat Control Operation

(Optional GHRCTA Series Only) The thermostat control set- ting on the remote control unit can be set to any comfort level between WARMER and COOLER. The burners will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

For wall thermostat operation, follow instruction supplied with thermostat accessory GWMT1. For wall switch operation fol- low instructions supplied with GWMS2.

NOTICE: You must light the pilot before using the remote control unit. See Lighting Instructions on page 25.

1. After lighting, let pilot flame burn for about one minute.

Turn control knob to ON position. Adjust flame adjust-

ment knob anywhere between HI and LO. Slide the selec-

tor switch to the REMOTE position. Note: The burner may

light if hand-held remote ON button was on when selector

GHRCTA Series Operation:

2b. Press the AUTO/ON/OFF button on the hand-held remote control (see Figure 53). The lights to the left of the button will show AUTO, ON, or OFF.

•In the ON mode, the burners will ignite. The fireplace is in manual mode when ON is lit.

•In the AUTO mode, the thermostat in the hand-held re- mote unit controls the room temperature. To increase the room temperature, press the top arrow of the TEMP but- ton. To lower the room temperature, press the bottom ar- row of the TEMP button. At higher settings the fireplace will run longer.

IMPORTANT: This remote control has been specially engi- neered to take an air temperature sample every 5.5 minutes in the auto mode. It will not respond immediately to the tem- perature setting being turned up or down.

IMPORTANT: The hand-held remote control unit must be near the fireplace. Do not keep the hand-held remote con- trol unit too close to the fireplace. The thermostat on the hand-held remote control unit will heat up too quickly and turn the fireplace off.

3.To turn the burner off, press the AUTO/ON/OFF button un- til OFF lights. The pilot will remain lit.

IMPORTANT: To turn the pilot off, manually turn the con- trol knob on the heater to the OFF position.

switch was last turned off. You can now turn the burner on

and off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch in the RE-

MOTE or ON position when the pilot is not lit. This will

drain the battery.

IMPORTANT: Be sure to press the ON/OFF buttons on the

hand held remote control unit for up to 3 seconds to assure

proper operation.

GHRC Series Operation:

2a. Press the ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit.

Shows

Temperature

Setting

The Log Fireplace will Automatically Cycle between Pilot and the

Heat Setting that has been Selected

Increases Room

Temperature in

AUTO Mode

Decreases

Room

Temperature in

AUTO Mode

Turns Burners

On or Off and

Allows You to

Choose the Auto

Setting

Selector Switch in Remote			Control Knob
Position (Optional Remote Control)			Control Knob
REMOTE			OL
REMOTE	N
OFF	N
OFF	O	F O
ON	T	F O
	O	F	HI
	LIP		HI

Flame Adjustment Knob

Figure 52- Setting the Selector switch, Control Knob, and Flame Adjustment Knob for Remote Operation

Figure 53 - Thermostat Hand-Held Remote Control Unit Selections (GHRCTA Only)

GWMT1 WALL MOUNTED

THERMOSTAT (OPTIONAL)

Make sure the heater switch is on AUTO and set the temperature adjustment on wall thermostat to the desired setting. The ther- mostat has been electronically calibrated at the factory and requires no adjustment or leveling.

Upon installation, the thermostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation. See installation instructions on page 21 of this manual.

For..com