3.Install low-pressure (black) nozzle into quick connect fitting of spray wand, refer to Spray Wand Nozzles. NOTE: Chemicals and soaps will not siphon if the black soap nozzle is not installed on the spray wand.

4.After use of chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. If chemicals remain in the pump it could be damaged. Pumps damaged due to chemicals will not be covered under warranty.

Starting

Warning: To reduce the risk of injury, read the pressure washer instruction manual and the engine instruction manual before starting pressure washer.

DANGER: Risk of fluid injection and laceration. When using the high-pressure setting, DO NOT allow the high-pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury will occur.

•Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fit- tings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately!

WARNING: Risk of fire, asphyxiation and burning. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank.

•Never fill fuel tank completely. Fill tank to 1/2" (12.7 mm) below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

•Never run engine indoors­ or in enclosed,­ poorly venti­lat­ed­ areas. Engine­ exhaust contains­ carbon monox­ide,­ an odorless and deadly gas.

•DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty.

NOTICE: Never pull water supply hose to move pressure­ washer. This could damage hose and/or pump inlet.

•DO NOT use hot water, use cold water only.

•Never turn water supply off while pressure washer engine is running or damage to pump will result.

• DO NOT stop spraying water for more than

two minutes at a time. Pump operates in

 

bypass mode when spray gun trigger is not

 

pressed. When the temperature inside the pump

 

rises too high the thermal relief valve (T) will open

T

and release a gush of water in an effort to lower

 

the temperature inside the pump. The thermal

relief valve will then close. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged.

Start-up Procedure

1.In a well-ventilated outdoor area, add fresh, high-quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine instruction manual for correct procedure.

2.Check engine oil level. Refer to the engine instruction manual for correct procedure.

3.Connect the water hose to the water source. Turn the water source on to remove all air from the hose. When a steady stream of water is present, turn the water source off.

English

13

Page 12 Page 14
Page 13
Image 13
DeWalt DXPW3025 instruction manual Starting, Start-up Procedure
Page 12 Page 14

DXPW3025 specifications

The DeWalt DXPW3025 is a high-performance pressure washer designed to tackle a variety of cleaning tasks with ease and efficiency. Known for its powerful engine and versatile features, this machine is a favorite among homeowners and professionals alike.

One of the standout features of the DXPW3025 is its robust 2.5 GPM (gallons per minute) water flow rate, which allows for superior cleaning power. The washer is equipped with a reliable 212cc engine that delivers impressive pressure levels, reaching up to 3000 PSI (pounds per square inch). This combination of high pressure and significant water flow makes it capable of removing even the toughest dirt, grease, and grime from various surfaces, including driveways, decks, and siding.

The design of the DXPW3025 emphasizes user convenience and portability. It features a compact frame and large wheels, which enable easy maneuverability across various terrains. Whether you need to navigate around the yard or transport it to a job site, this pressure washer is built for mobility. Additionally, the ergonomic handle ensures a comfortable grip, reducing fatigue during extended use.

Technologically, the DXPW3025 incorporates several advanced features that enhance its functionality. It includes an adjustable pressure control system that allows users to customize the pressure output based on the task at hand. This not only optimizes cleaning efficiency but also helps to protect delicate surfaces from potential damage.

Furthermore, the DeWalt DXPW3025 comes with a variety of nozzle options, including a 0-degree nozzle for targeted cleaning and a 40-degree nozzle for wider coverage. This versatility means users can switch between different spray patterns quickly based on their specific needs.

Safety is also a priority with the DXPW3025, as it is equipped with a thermal relief valve that prevents overheating during extended use. This feature contributes to the longevity and reliability of the machine, ensuring it remains a valuable asset for years to come.

In summary, the DeWalt DXPW3025 pressure washer combines powerful performance, user-friendly design, and advanced features, making it an excellent choice for anyone looking to tackle tough cleaning tasks efficiently. Whether for residential or commercial use, this model represents a solid investment that delivers impressive results.
Top Page Image Contents