Manuals / Dish Network / TV and Video / Universal Remote

Dish Network 3.1, 3.0, 3.2 warranty Press the STAR * button

Models: 3.0 3.2 3.1

1 46

Download 46 pages 53.96 Kb

Page 19

USING THE RECOVER BUTTON

Use this procedure works only if you have accidentally changed the TV channel or video input. It does not recover lost satellite signal.

Note: RECOVER will first try to tune your TV to channel 3, then channel 4, and then other video inputs with each press of the RECOVER button. You may need to press the RECOVER button up to 30 times to recover your satellite TV video.

1.Press and hold the RECOVER button until all four mode buttons light, and then let go of the button. The SAT mode button flashes twice and then all four mode buttons flash three times.

2.Press the RECOVER button. Wait for the TV mode button to flash once and then all four mode buttons to flash once.

3.If you see the System Info screen, press the SELECT button to close the screen. You have recovered your satellite video.

4.If you do not see the System Info screen, repeat steps 2 and 3 until you have recovered your satellite video.

Note: Press any remote control button other than the RECOVER button to end this procedure.

PROGRAMMING THE RECOVER BUTTON TO TUNE THE TV TO A SPECIFIC CHANNEL

The RECOVER button can be programmed to tune your TV back to the TV channel you use to watch satellite programming.

1.Program your remote to control your TV using the instructions in Setting Up to Control Other Devices on page 8.

2.Press and hold the TV mode button until all the other mode buttons light up, and then let go of the button. The TV mode button flashes.

3.Press the STAR (*) button.

4.Enter the three digits of your channel number. For example, if your remote TV is set to channel 60, enter 0-6-0.

5.Press the POUND (#) button. The TV mode button flashes three times.

18

Image 19

Dish Network 3.1, 3.0, 3.2 warranty Press the STAR * button

Contents

REGULATORY FACTORS SAFETY INSTRUCTIONSWIRELESS REMOTE CONTROL INSTALLATIONTABLE OF CONTENTS MODELS SUPPORTED BY THIS GUIDE REMOTE CONTROL BASICSUHF AND IR SIGNALS INSTALLING BATTERIESCONVERTING THE 4.0 REMOTE CONTROL SETTING UP TO CONTROL THE SATELLITE RECEIVER Primary Remote Address and a Secondary Remote Address b. Select Enable from the TV1 UHF Pro Setup screenCHECKING THE REMOTE ADDRESS LIMITED MODE SETTING UP TO CONTROL OTHER DEVICESSETTING UP USING DEVICE CODE TABLES COMBINATION DEVICES6. Only for limited mode, Press SETTING UP USING DEVICE CODE SCANCHECKING THE DEVICE CODES To set the remote to control the device’s volume SWITCHING BETWEEN TV AND DEVICE VOLUME CONTROLTo set the remote back to control the TV volume OPERATING MODES REMOTE CONTROL OPERATIONTV/VIDEO BUTTON POWER BUTTONSVOLUME BUTTON CONTROLLING THE SATELLITE RECEIVER SAT MODE BUTTONGUIDE BUTTON MUTE BUTTONMENU BUTTON PAGE UP AND PAGE DOWN BUTTONSINFO BUTTON ARROW BUTTONSSELECT BUTTON RECALL BUTTONNUMBER BUTTONS CANCEL BUTTONVIEW TV BUTTON DISH BUTTONSTAR * BUTTON RECOVER BUTTONPOUND # BUTTON 3. Press the STAR * button TV/VIDEO BUTTON CONTROLLING A TV OR A SECOND TVTV MODE BUTTON POWER BUTTONSRECALL BUTTON UP/DOWN ARROW BUTTONSVOLUME BUTTON SELECT BUTTONOnly the buttons described here control a VCR or DVD player. Some of the buttons we tell you about here may not control your VCR. See your VCR or DVD player user’s manual for information about the features POWER BUTTONCONTROLLING A VCR OR A SECOND VCR OR A DVD PLAYER VCR MODE BUTTONVIEW TV BUTTON PAGE UP/DOWN ARROW BUTTONSVCR BUTTONS Use these buttons to change channels on the VCRVOLUME BUTTON CONTROLLING A TUNER OR AMPLIFIERAUX MODE BUTTON POWER BUTTONUse these buttons to change channels on the tuner or amplifier UP/DOWN ARROW BUTTONSSELECT BUTTON TV Codes DEVICE CODESCodes CodesCodes CodesCodes CodesCODES VCR CODESCODES CODES CODESTV/VCR TV/VCR COMBO CODESDVD PLAYER CODES CODESTuner TUNER/AMPLIFIER CODESDVD Players CodesCODES DVD/VCR COMBOTV/DVD COMBO CODES Programming for combination equipmentWhat’s TROUBLESHOOTINGSee Setting Up to Control the address see Setting Up to ControlWhat’s to use. See Remote Control Setupaddress see Setting Up to Control See Setting Up to Control OtherLIMITED WARRANTY ADVANCE EXCHANGE PROGRAM POST RECEIPT EXCHANGE PROGRAM ACCESSORY WARRANTY2. See Troubleshoot the Remote on page IF YOU NEED HELPPage Page Page Page Page Technical Publications, 94 Inverness Terrace East Englewood, Colorado EchoStar Technologies CorporationCopyright EchoStar Technologies Corporation Englewood, Colorado