Manuals / Draytek / Computer Equipment / Network Router

Draytek 2130 manual For Windows

Models: 2130

1 208

Page 202

5.2Checking If the Network Connection Settings on Your Computer Is OK or Not

Sometimes the link failure occurs due to the wrong network connection settings. After trying the above section, if the link is stilled failed, please do the steps listed below to make sure the network connection settings is OK.

For Windows

1.Go to

The example is based on Windows XP. As to the examples for other operation systems, please refer to the similar steps or find support notes in www.draytek.com.

Control Panel and then double-click on Network Connections.

2.Right-click on Local Area Connection and click on Properties.

3.Select Internet Protocol (TCP/IP) and then click Properties.

194	Vigor2130 Series User’s Guide

Page 202

Image 202

Contents

Page Version Date 31/08/2009 Vigor2130 Series High Speed Gigabit Router User’s GuideVigor2130 Series User’s Guide Safety Safety Instructions and ApprovalCopyright Information WarrantyEuropean Community Declarations Regulatory InformationTable of Contents 4 AdminModeOperation Vigor2130 Series User’s Guide4.3.1 Hardware NAT 5 Trouble Shooting 1.1 Web Configuration Buttons Explanation 1 PrefaceStatus 1.2 LED Indicators and Connectors1.2.1 For Vigor2130 ExplanationConnector for a power adapter Factory Resetfactory default configuration Power SwitchExplanation 1.2.2 For Vigor2130nStatus InterfaceConnector for a power adapter Factory Resetfactory default configuration Power SwitchExplanation 1.2.3 For Vigor2130VnStatus InterfaceInterface Description1.3 Hardware Installation c d e f Stand InstallationVigor2130 Series User’s Guide 1.4 Printer Installation 2. Open Start-Settings- Printer and Faxes4. Click Local printer attached to this computer and click Next Vigor2130 Series User’s Guide8. Then, in the following dialog, click Finish 7. Click Standard and choose Generic Network CardVigor2130 Series User’s Guide 9. Now, your system will ask you to choose right name of the printer that you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router 2.2 Accessing Web Page 2 Configuring Basic Settings2.1 Two-Level Management Main screen for admin mode operation full configuration 2.3 Changing PasswordMain screen for user mode operation simple configuration 5. Type New Password in New Password and Confirm New Password fields. Then click OK to continue 2.4.1 Setting up the Password 2.4 Quick Start Wizard2.4.2 Setting up the Time Zone 2.4.3 Setting up the Internet ConnectionIP Address Static IPEnable Subnet MaskEnable DHCPPPPoE Clone MAC AddressIt means Max Transmit Unit for packet. The default setting issetting is It means Max Transmit Unit for packet. The defaultPPTP/L2TP 2.4.4 Setting up the Wireless Connection Choose Show to make the SSID being seen by wireless clientsPage WPA Algorithm WPA-PSKType WPA Pre-shared KeyWPA- RADIUS The UDP port number that the RADIUS server is using. TheShared Secret 2.4.5 Save the Wizard Configuration 2.5 Online Status2.6 Saving Configuration 3.1 WAN 3 User Mode OperationBasics of Internet Protocol IP Network Get Your Public IP Address from ISP From 10.0.0.0 to From 172.16.0.0 to From 192.168.0.0 toWhat are Public IP Address and Private IP Address Network Connection by 3G USB Modem3.1.1 Internet Access StaticType in the primary IP address for the router if you want to use PPPoE Type in the username provided by ISP in this fieldDHCP UsernameIt means Max Transmit Unit for packet. The default setting is It means Max Transmit Unit for packet. The defaultPPTP/L2TP 3G USB Modem APN means Access Point Name which is provided andrequired by some ISPs Port 3.1.2 PortsSpeed Configured LinkDiscard - It determines whether the MAC drops frames after an 3.1.3 3G Backupexcessive collision has occurred. If yes, a frame is dropped after APN means Access Point Name which is provided and 3.2 LANBasics of LAN required by some ISPsWhat is Routing Information Protocol RIP What are Virtual LANs and Rate ControlType in an address code that determines the size of the network 3.2.1 General SetupYou can configure the router to serve as a DHCP server for the Enter a value of the IP address pool for the DHCP server to startPort 3.2.2 PortsSpeed Configured LinkDisabled All power savings mechanisms disabled 3.2.3 MAC Address TablePower Control ActiPHY Link down power savings enabledStatic MAC Table Config 3.2.4 VLANDisable Automatic Aging Age TimeDestination Address 3.2.5 Static RouteIndex Display the destination address of the static routeAdd Static Routes to Private and Public Networks 3.2.6 Bind IP to MAC and MAC address listed in ARP table can be selected and added 3.3 NATand select the one, and click Remove. The selected item will be 3.3.1 Hardware NAT 3.3.2 Open PortsProtocol Specify the name for the defined network serviceName Specify the transport layer protocol. It could be TCP, UDP and3.3.3 DMZ Host 3.4 Bandwidth Management 3.4.1 Session Limit3.4.2 Bandwidth Limit 3.4.3 Port Rate Control Shaper Rate Tx 3.4.4 QoS Control ListShaper Unit Type Value QCE TypeDisplay the type of that QCE QoS Control Entries Display the value specified for the QCEAdding a New QCE TCP/UDP Port Moving Up/Down a QCE 3.4.5 Ports PriorityEditing a QCE Deleting a QCEQueuing Mode 3.4.6 QoS StatisticsDefault Class Use the drop down list to choose suitable modeRx Packets Rx Low 3.5 Applications 3.5.1 Dynamic DNS3.5.2 Schedule Check the box to enable this function 3.5.3 IGMP SnoopingSnooping Enabled Check the box to enable unregistered IPMC traffic floodingDisplay current IGMP groups. Maximum number of group 3.5.5 UPnP Configuration3.5.4 IGMP Status for each VLAN can be set isCant work with Firewall Software 3.6 Wireless LAN 3.6.1 Basic Concepts3.6.2 General Setup Security OverviewSSID Broadcast Wireless Security ConfigurationWireless Mode SSIDWPA Mode Default KeyAuthentication Mode Key1-Key4Either 8~63 ASCII characters, such as 012345678..or Vigor2130 Series User’s Guide 3.6.3 Access Control Filter Type3.6.4 Station List 3.7.1 USB General Settings 3.6.5 Access Point Discovery3.7 USB Application after clicking OK, the router will create the specific/new 3.7.2 FTP User ManagementThe user can enter a directory name in this field. Then folder in the USB diskette. In addition, if the user types “/”3.7.3 Disk Status here, he/she can access into all of the disk folders and filesNote When write protect status for the USB diskette is 3.7.4 Disk SharesType a name to be used as shared folder name in Samba service 3.8 User 3.8.1 User ConfigurationAdding a New User Editing/Deleting User Settings 3.9 System Maintenance3.9.1 System Status Wireless LAN 3.9.3 Configuration Backup 3.9.2 User PasswordBackup the Configuration Restore Configuration 3.9.4 Syslog / Mail Alert Check the box to activate function of mail alert Select the time zone where the router is located 3.9.5 Time and DateVigor2130 Series User’s Guide 3.9.6 Management 3.9.7 Reboot SystemAccess List 3.9.8 Firmware Upgrade Vigor2130 Series User’s Guide Basics of Internet Protocol IP Network 4 Admin Mode Operation4.1 WAN From 10.0.0.0 to From 172.16.0.0 to From 192.168.0.0 toGet Your Public IP Address from ISP What are Public IP Address and Private IP AddressNetwork Connection by 3G USB Modem Static 4.1.1 Internet AccessType the subnet mask DHCP PPPoEIt means Max Transmit Unit for packet. The default setting issetting is It means Max Transmit Unit for packet. The defaultPPTP/L2TP 3G USB Modem APN means Access Point Name which is provided andrequired by some ISPs 4.1.2 Ports You can use the drop down list to choose the required speed forInternet 4.1.3 3G BackupSIM PIN code required by some ISPs 4.2 LANAPN means Access Point Name which is provided and Basics of LANWhat is Routing Information Protocol RIP What is Static RouteVigor2130 Series User’s Guide 4.2.1 General Setup What are Virtual LANs and Rate ControlStart IP Address 4.2.2 PortsSpeed Configured IP Pool CountsAuto Static MAC Table Config 4.2.3 MAC Address TableDisable Automatic Aging Age Time4.2.4 VLAN 4.2.5 Static Route Add Static Routes to Private and Public NetworksVigor2130 Series User’s Guide 4.2.6 Bind IP to MAC 4.3 NAT 4.3.1 Hardware NAT 4.3.2 Open PortsProtocol Specify the name for the defined network serviceName Specify the transport layer protocol. It could be TCP, UDP andCheck to enable the DMZ Host function 4.3.3 DMZ HostEnable DMZ IP4.4.1 DoS Defense Denial of Service DoS Defense4.4 Firewall Basics for Firewall4.4.2 Ports Configuration Rate Limited ID include Disabled, and 1 to 10. The default value is DisabledCounts the number of frames that match this Access Control Port CopyRate limiter ID will be applied to WAN port and LAN port 4.4.3 Rate Control ObjectPlease specify a rate number for each ID. The default setting is “1”packet per second4.4.4 Access Control List Adding a New Access Control ProfileAction - it means the session limitation for this access control list will be applied to if matching with the rule defined in this page Specify the destination MAC filter for this ACE MAC ParameterVLAN Parameter Ethernet Type Filter Detailed Explanation for Frame TypeARP/RARP defined in Sender IP Address and Sender IP Mask Request/ReplySender IP Filter Sender IP Address0 ARP/RARP frames where the hardware address space is 0 means ARP/RARP frames/packets where the hardware1 means ARP/RARP frames/packets where the hardware 1 ARP/RARP frames where the hardware address space isIP Option IP TTLIP Fragment OFFSET field is greater than zero must be able to matchSIP Mask SIP FilterSIP Address DIP FilterIP TTL ICMP Code FilterICMP Code Value IP FragmentSIP Address IP OptionSIP Filter SIP MaskSource Port Range Source Port FilterSource Port No Dest. Port FilterIP Fragment IP TTLIP Option SIP Mask SIP FilterSIP Address DIP FilterDest. Port Filter 0 TCP frames where the FIN field is set must not be able0 TCP frames where the SYN field is set must not be able Specify the TCP port destination filter for this ACETCP PSH 0 TCP frames where the PSH field is set must not be able0 TCP frames where the ACK field is set must not be able TCP ACKIP Fragment IP Protocol ValueIP TTL IP OptionSIP Address 4.5 Bandwidth ManagementSIP Filter SIP Mask4.5.1 Session Limit Disable 4.5.2 Bandwidth LimitEnable Default TX limit4.5.3 Port Rate Control 4.5.4 QoS Control ListVigor2130 Series User’s Guide Display the type of that QCE QoS Control Entries Adding a New QCEQCE Type Type ValueTCP/UDP Port Editing a QCE Deleting a QCE 4.5.5 Ports PriorityMoving Up/Down a QCE Indicate the interface for the physical port, WAN port, LANUse the drop down list to choose suitable mode 4.5.6 QoS StatisticsQueuing Mode Queue WeightedRx Packets Rx Low 4.6 Applications 4.6.1 Dynamic DNS4.6.2 Schedule Check the box to enable this function 4.6.3 IGMP SnoopingSnooping Enabled Check the box to enable unregistered IPMC traffic floodingDisplay current IGMP groups. Maximum number of group 4.6.5 UPnP Configuration4.6.4 IGMP Status for each VLAN can be set isUPnP clients Enter the maximum sustained WAN download speed inkilobits/second. Such information can be requested by Enter the maximum sustained WAN upload speed in4.7 VPN and Remote Access 4.7.1 Remote Access Control4.7.2 PPTP Remote Dial-in Adding a New UserEditing/Deleting User Settings Vigor2130 Series User’s Guide4.7.3 IPSec Remote Dial-in Mobile VPN TypeAdvanced Settings AuthenticationIdentities 4.7.4 Remote Dial-in Status Display the encryption and authentication algorithm usedduring phase 1 of the VPN connection Establishment. The algorithm is used during exchange of key exchangeDisplay the encryption and authentication algorithm used 4.7.5 LAN to LANAdding a VPN Tunnel during phase 1 of the VPN connection Establishment. TheRemote IP EnabledName Type4.8 Wireless LAN 4.8.1 Basic ConceptsSecurity Overview Wireless Mode 4.8.2 General SetupEnable Wireless LAN SSID BroadcastAuthentication Mode Wireless Security ConfigurationDefault Key z NoneWPA Preshared Key WPA ModeWPA Algorithm z WPA-RADIUSDestination Port WPA AlgorithmServer IP Address Shared Secret4.8.3 Access Control Vigor2130 Series User’s Guide4.8.4 Station List 4.8.5 Access Point Discovery 4.9 USB ApplicationEnable FTP 4.9.1 USB General Settings4.9.2 FTP User Management Enable Disk Sharing4.9.3 Disk Status 4.9.4 Disk SharesThe user can enter a directory name in this field. Then here, he/she can access into all of the disk folders and filesNote When write protect status for the USB diskette is after clicking OK, the router will create the specific/new4.10 User 4.10.1 User ConfigurationAdding a New User Editing/Deleting User Settings Vigor2130 Series User’s Guide4.11 System Maintenance 4.11.1 System Status4.11.3 User Password 4.11.2 System PasswordDisplay the subnet mask address of the WAN interface 4.11.4 Configuration Backup Backup the Configuration4.11.5 Syslog/Mail Alert Restore ConfigurationEnable Syslog Access… Add NTP server 4.11.6 Time and DateTime Zone Click the button to add a new NTP server4.11.7 Management 4.11.8 Reboot SystemClick this button to remove an NTP server 4.11.9 Firmware Upgrade 4.12 Diagnostics 4.12.1 Ping4.12.2 Routing Table D - dynamically installed by daemon or redirectA - installed by addrconf Display the netmask for the destination netTime 4.12.3 System Log4.12.4 Traffic Overview Level4.12.5 Detailed Statistics Rx Unicast 4.12.6 MAC Address Table MAC Address TypeVLAN Port Members4.12.7 DHCP Table It displays the name of the computer accepted the assigned4.12.8 Data Flow Monitor Block - can prevent specified PC accessing into Internet4.12.9 Ports State connection. Or you can check Auto-refresh to reload the5 Trouble Shooting 5.1 Checking If the Hardware Status Is OK or NotFor Windows 2. Open the Application folder and get into Network For MacOs1. Double click on the current used MacOs on the desktop Vigor2130 Series User’s GuideFor MacOs Terminal 5.3 Pinging the Router from Your ComputerFor Windows 5.4 Checking If the ISP Settings are OK or Not Vigor2130 Series User’s Guide1. Choose Static IP as the connection type For Static UsersFor PPPoE Users 1. Choose PPPoE as the connection typeSoftware Reset 5.5 Backing to Factory Default Setting If NecessaryFor PPTP/L2TP Users Hardware Reset 5.6 Contacting Your Dealer