When selecting the Function Select for Room | DTS RV4700 DTS-ES

When selecting the FUNCTION SELECT for ROOM 2

Press the CURSOR UP( )/DOWN( ) buttons to select the FUNCTION SELECT for ROOM 2 source,

1 then press the ENTER button

VOL. CH LEVEL

ENTER

F U N C T I O N

R O O M 2 F E E D T U N E R

CD

A U X

S E L E C T

: Off

V I D E O 1 V I D E O 2 V I D E O 3 V I D E O 4

HOME THEATER MASTER

RV4700 DTS-ES

E N T E R : S e t

, , , : M o v e

Press the CURSOR LEFT( )/RIGHT( ) buttons to select the ROOM 2 FEED mode as desired.

2

VOL. CH LEVEL

•Each time these buttons are pressed, the ROOM 2 FEED mode is changed to “On” or “Off”.

•When the ROOM 2 FEED mode is set to “Off”, the ROOM 2 source cannot be selected.

•When you do not use the ROOM 2 function, set the ROOM 2 FEED mode to Off to save electricity.

HOME THEATER MASTER

RV4700 DTS-ES

When the ROOM 2 FEED mode is set to On

Press the CURSOR UP( )/DOWN( )/LEFT( )/RIGHT( ) buttons to select the desired ROOM 2

3 source, then press the ENTER button.

VOL. CH LEVEL

ENTER

HOME THEATER MASTER

RV4700 DTS-ES

•Each time the CURSOR CONTROL buttons are pressed, “+” is moved to the corresponding input source.

•When the audio input source is selected, a video input source can be marked with “+”, too.

It means that the image of the video input source selected previously can be played separately, too.

47

Image 47

DTS RV4700 DTS-ES manual When selecting the Function Select for Room, When the Room 2 Feed mode is set to On

Contents

RV4700 DTS-ES Introduction Unpacking and Installation AC Voltage Selection Read this Before Operating Your Unit Contents System Connections Connecting Antennas Connecting Audio ComponentsConnecting 7.1CH Direct INPUTs Front SUR Round Back Connecting Video Components PRE OUT connections Connecting MULTI-ROOM System KITConnecting Digital INs and OUT Room 2 connections Switched AC OutletAC Inlet Connecting Speakers Fluorescent Display Front Panel Controls LED Lamp Device Buttons Universal Remote Controls Function Table of the Numbered Buttons Loading Batteries Remote Control Operation Range Functions Codes Additional Information on Remote Command Codes For Power ON/OFF Entering a Setup Code Tape Monitor function When selecting the 7.1 CH Direct as desiredOperations Before operation Adjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selected Sound tracks Surround modes Surround Sound Stadium TheaterMovie Hall 1/2 Surround back left and right speakers Speaker placementFront left and right speakers and center speaker Surround left and right speakers Enjoying Surround Sound Selected decoding mode as follows When canceling the surround mode for normal stereo operation Select the desired channel Adjusting each channel level Downmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stations Scanning preset stations in sequence Tuning to preset stations Listening to RDS Broadcastsfm only Additional Function for RV4700 DTS-ES RDS Tuner Only Information EON PTY EON Enhanced Other Networks Dubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape Monitor Digital Audio Recording with MD Recorder Compressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other Functions Correcting or clearing a video label Entering a video label Room 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the desired input source When selecting the CH Level Trim When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the Function Select When selecting the Speaker Config Setting the Speaker Setup When selecting the Speaker Distance When selecting the LFE Level Control When selecting the Digital in Setup Setting the Function SelectWhen selecting the Input Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the surround mode When selecting the Decoding Mode Setting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed Setup When the Room 2 Feed mode is set to On When selecting the Function Select for Room Problem Possible Cause Remedy Troubleshooting Guide Specifications RV4700 DTS-ES