Manuals / Dynacord / Home Audio / Stereo Equalizer

Dynacord DSP 244 Send Parameters, To MIDI, To RS232, 9.9 RS-232TO MIDI data transmission

Models: DSP 244

1 51

Download 51 pages 3.38 Kb

Page 39

9.8 SEND PARAMETERS

O P T I O N

You can select one of the following settings for the MIDI TX CHANNEL:

Off:

No MIDI DATA is transmitted.

1 - 16:

The DSP 244 transmits MIDI DATA via the selected MIDI channel 1 to 16.

9.8 SEND PARAMETERS

During editing or when sending a program change command, the DSP 244 is capable of transmitting its parameters in real time via the serial port(s). A complete parameter dump of the new program is automatically carried out during program changes. This ensures that settings of receiver and sender are identical. The function also provides the possibility to control additional DSP 244 (Master-Slave-Operation) or to send data to the DSP 244 Editor which then are displayed on the PC-screen.

This page allows you to adjust whether data is being transmitted, and if so, which interface is going to be used.

Off:

No data is transmitted.

To MIDI:

During editing and program change, data is transferred via the previously set MIDI-transmission channel (MIDI TX CHANNEL). This allows to control a single or several connected DSP 244 slave units from one master. All parameters and program changes are simultaneously set for the slave and master units. Before connecting several units, always make sure that they all are adjusted to identical programs and parameter settings.

To RS232:

During editing and program change, data is transmitted via the RS-232 port. In case that you have connected a PC with the DSP 244 Editor software installed, you are able to monitor changes in the setting on the PC-screen.

9.9 RS-232 TO MIDI data transmission

This function provides the possibility to pass data that is received over the RS-232 port on to the MIDI OUT port, which offers the opportunity to create a so called “RS-232 to MIDI Bridge” from the master unit. Whenever several DSP 244 are included in a MIDI chain, connect the DSP 244 master via RS-232 interface to your computer, and control the master (via RS-232) as well as the DSP 244 slaves (via MIDI) from the PC.

9-4

Image 39

Dynacord DSP 244 owner manual Send Parameters, To MIDI, To RS232, 9.9 RS-232TO MIDI data transmission, O P T I O N

Contents

24 BIT DIGITAL SOUND SYSTEM PROCESSOR For US and CANADA only IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SERVICE INSTRUCTIONS TABLE OF CONTENTS CONTENTS1. INTRODUCTION 1.1 DSP 244 FEATURES1.2 UNPACKING AND WARRANTY INTRODUCTION2, Level meters CONTROLS AND CONNECTIONS2. CONTROLS AND CONNECTIONS 2.1 FRONT PANEL 1, Control INPUT 1 / INPUT16, POWER ON/OFF-switch 13, Channel function indicators SUB, LO, MID, HI14, Level meter indicators OUTPUT 15, Compressor indicators OUTPUT21, IN 1 / IN 2 connectors 2.2 REAR PANEL 17, Mains connector19, MIDI IN / THRU / OUT connectors 20, OUT 1 - 4 connectors3.2 Unbalanced INPUT/OUTPUT configuration INSTALLATION AND CONNECTIONS3. INSTALLATION AND CONNECTIONS 3.1Balanced INPUT/OUTPUT configuration4. FIRST OPERATION 4.1 SWITCHING THE POWER ON4.2 LEVEL SETTINGS FIRST OPERATION5. QUICK START POWER-ONOPERATIONLEVEL SETTING QUICK STARTQUICK START X-OVERSETTINGSDELAY ALIGNMENT LOUDSPEAKER EQUALIZATIONCOMPRESSOR / LIMITER SETTINGS MATCHING THE FREQUENCY RESPONSEQUICK START 3 Way + Fullrange 3 Way / Mono Sub + Fullrange CONFIGURATIONS OF THE DSP6. CONFIGURATIONS OF THE DSP Stereo 2 Way Stereo 2 Way / Mono Sub + FullrangeC O N FIGURATIONS OF THE DSP 6.1 Stereo 2 Way6.2 Stereo 2 Way / Mono Sub + Fullrange 6.3 3 Way + Fullrange 6.4 3 Way / Mono Sub + FullrangeCONFIGURATIONS OF THE DSP 6.5 3 Way / Independent Sub + Fullrange 6.6 4 WayC O N FIGURATIONS OF THE DSP CONFIGURATIONS OF THE DSP 6.7 2-IN-4Program selection Initial state after power-onoperationO P E R A T I O N 7. OPERATION7.1 PROGRAM SELECTION 7.2 EDITINGO P E R A T I O N O P E R A T I O N 3.Whenever the function block in the first line is selected, you are able to select another function block by using the rotary encoder 10. Pressing one of the controls OUT 1 - 4 lets you directly select the function blocks of the corresponding output channelO P E R A T I O N 7.3 STORE PROGRAMS AND PROGRAM NAMESO P E R A T I O N 7.4 MODIFYING FACTORY PRESET PROGRAMS8. PARAMETERS P A R A M E T E R S8.1 PARAMETER ACCESS 8.1.1 PARAMETER ACCESS-TABLEP A R A M E T E R S MASTER EQ1-5 Default8.1.2 PARAMETER LINK-TABLE 8.2 DESCRIPTION OF PARAMETERSf = 1kHz, Q = P A R A M E T E R Sf = 1kHz, Gain = -12dB P A R A M E T E R SDefault MASTER DELAYROUTING DefaultCHANNEL EQ1-4 DefaultP A R A M E T E R S ALLPASS f = 1kHz, Order = 1st, 2nd Q = P A R A M E T E R SDefault HIPASS X-OVERLOPASS X-OVER DefaultBessel 12 dB Butterworth 12 dB Bessel 18 dB P A R A M E T E R SCHANNEL DELAY DefaultP A R A M E T E R S COMPRESSOR DefaultP A R A M E T E R S Settings / Value range LIMITERLEVEL Default9.2 EDIT MODE SELECTION 9.1 SETTING THE LCD CONTRASTO P T I O N 9. OPTION FUNCTIONSdB from Clip 9.3 COMPRESSOR AND LIMITER THRESHOLD UNITVolts dBuFahrenheit 9.6 TEMPERATURE UNIT settings9.7 MIDI RX / TX CHANNEL settings Celsius9.9 RS-232TO MIDI data transmission 9.8 SEND PARAMETERSTo MIDI To RS232O P T I O N 9.10 NRS 90246 CONTACT CLOSURE INTERFACE settingsPGM Mute 9.11 NRS 90247 RS-485INTERFACE SETTINGSCNTCT PGM U0110. SPECIFICATIONS 10.1 TECHNICAL SPECIFICATIONSS PECI F I C A T IO N S 10.2.2 MIDI SYSTEM EXCLUSIVE IMPLEMENTATION 10.2.1 GENERAL MIDI COMMANDSM IDI 10.2 MIDISerial Link M IDIValue Command Parser Code TableUNIT-ID TreeInstallation instructions NRS RETROFITTING INSTRUCTIONS10.3 RETROFITTING INSTRUCTIONS RETROFITTING INSTRUCTIONS 10.3.2 Installation manuals for interface cards10-7 BLOCKDIAGRAMM / BLOCK DIAGRAM10-5 FLUSSDIAGRAMM / FLOW DIAGRAMABMESSUNGEN / DIMENSIONS Abmessungen / Dimensions in mm10-6 WARRANTY GARANTIEGARANTIE