Manuals / Eiki / Computer Equipment / Projector

Eiki PJNET-300 owner manual Change the mode of the registered projector, Status

Models: PJNET-300

1 86

Download 86 pages 31.75 Kb

Page 59

Change the mode of the registered projector

Multi-control

Change the mode of the registered projector

To change the mode of the registered projector, select a mode with the pull-down menu button under the IP address of the target projector and then click Set button.

Mode	Operation
Control	Multi-controlling the projector
OFF	Excluding from the multi-control
Delete	Deleting from the multi-control

* This function is not available with the Light mode.

Status

If some of the registered projectors are disabled by some reasons (such as disconnecting the power source, disconnecting the LAN cable, disconnecting from the network), control changes will continue to be effective for the projectors that are still active. At the same time, the deactivated projectors are excluded from the multi-control. The status of the registered projectors are indicated under the projec- tor name. See the table below for status indications.

	Status
Status	Description
(blank)	The projector is connected to the network correctly
No connect	The projector may not be connected to the network. Please check the connection and
	network configuration of this projector.
PIN code error	The PIN code is incorrect. The PIN code for the multi-controlled projectors must be
	the same. Change the PIN code of this projector to the common PIN code.

* The Network Unit updates the status at the time when the multi-control function was executed.

✐If the multi-controlled projector is in the standby mode, any change is not effective except timer setting.

✐It is recommended that a specified projector should be chosen for setting as a master when you use this multi-control function. The control for the multi-controlled projectors will become too complicated operation if this function is used for each projector.

✐If the registered projector is not connected to the network, it will take some time to complete the multi-control operation because of waiting for the response from each registered projector.

OWNER'S MANUAL

ENGLISH

59

Image 59

Eiki PJNET-300 owner manual Change the mode of the registered projector, Status

Contents

OWNERS MANUAL PjNET-300Federal Communication Commission Notice ComplianceENGLISH CAUTION ON USE IN NETWORKChapter 3 Basic Setting and Operation ContentsChapter 2 Installation ENGLISH ContentsPage ENGLISH ChapterPreparation Describes features and operating environment of this productSNMP Agent function p.36 FeaturesWeb Management function p.39 E-Mail Alert function p.32time Automatic On/Off using Clock function p.51Multi-control function p.56 Control port ready for external equipment p.61Computer Operating environmentOperating System NetworkOwner’s manual Before usePackage contains Network UnitThe contents of this manual are subject to change without notice Expression/AbbreviationUse of this manual TrademarksOWNSERS MANUAL Chapter InstallationDescribes how to install the Network Unit, and configure the network ENGLISH1 Function of the Network Unit p.15 Flow of installation2 Installation and network configuration p.16-22 Set up is completeConnector plug Power indicatorACT indicator LINK indicatorMounting 2 Installation and network configurationInstallation and network configuration Connection of LAN cable1 Selection of network menu Network configurationConfigure the network Confirmation of the network menuCompleting of installation 2 Configuration for IP Address/ Sub net/ Gateway*1/DNS*2How to enter the numbers 3 Fixing the network configuration2 Entering the network PIN code Network PIN code settingDefault network PIN code 0000 means no network PIN code is set 1 Displaying network PIN code menuHow to enter the numbers with the screen 10-key pallet Notice about system construction OWNSERS MANUAL Chapter 3 Basic Setting and OperationENGLISH 1 Enter the IP address Login the setting page of the projector2 Select a display mode and login Setting page 3 Display of main setting pagez Main setting page in the Standard Mode display Login the setting page of the projectorx Main setting page in the Light Mode display How to use the setting pageRadio button setting Type of the setting palletText box setting Pull-down menu settingUse of Battery Initial settingInitial setting PJLink and password settingWhats PJLink? Network PIN code settingManual setting Date and time settingAuto setting Network configuration Network configuration1 Setting SMTP server and administrator address E-mail settingE-mail setting 2 Registering and deleting E-mail addresses3 Option selection for sending alert mail Chapter 3 Basic Setting and Operation Examples Type and contents of alert mailWhen internal PJ temperature is too high When internal PJ power circuit is failedENGLISH When the life span of lamp is reachedWhen lamp corres. value reaches preselect use time E-mail settingChapter 3 Basic Setting and Operation SNMP settingENGLISH Trap option settingSNMP setting Check and delete the trap addressChapter 3 Basic Setting and Operation OWNSERS MANUAL Chapter Controlling the ProjectorENGLISH Chapter 4 Controlling the Projector Power control and status checkStatus About projector conditionPower control and status check ENGLISHInput ControlsSystem Available selection when the ComputerAnalog inputAvailable selection when the VIDEO/S-VIDEO input Available selection when the Y, Pb/Cb, Pr/Cr inputDescription Image adjustmentImage mode Chapter 4 Controlling the Projectorclicking ON or OFF button SoundMenu Suppresses the sound. ON, OFFDisplay area PC adjustmentChapter 4 Controlling the Projector Item DescriptionENGLISH Setting up the projectorSetting up the projector Screen mode VideoItem Description Lamp Corres. Value ResetChapter 4 Controlling the Projector DescriptionSave/delete the settings Save the controls and settingsClick Stop button to cancel the auto page display Check the saved itemsLoad a control set 1 Set a day or date Timer settingHow to set the timer 3 Select an event action Check the timer eventsChange the event mode 2 Set an execute timeENGLISH Notes on timer settingTimer setting Items Projector informationClick this button to update the information Chapter 4 Controlling the ProjectorENGLISH Indication of the lamp statusProjector information Chapter 4 Controlling the Projector Controlling and setting the multi-projectorsMulti-control Example of multi controlMulti control setting Start/stop the multi controlConfirmation of registered projector Register the projectorStatus Change the mode of the registered projectorThis indicates that the mode is Control Conf. & Change page in the light modeSetting all together Controlling all togetherOWNSERS MANUAL Chapter Use of Serial PortENGLISH Chapter 5 Use of Serial Port Serial port settingof the serial controller Setting examples for the serial controlLAN cable Control examplesExample Chapter 5 Use of Serial PortENGLISH ExampleControl examples Serial controllerControl Use of telnetPreparation When the word Hello is replied, login has been succeeded Command list table Control the projector with telnetENGLISH Examples of connection Web browser setting Technical data Q & AAppendix ChapterTo another network Examples of connectionPeer-To-Peer connection Chapter 6 AppendixTo another network The gateway Router installed in the networkEntrance hall Gateway RouterProxy setting Web browser settingActive Script/JavaScript enable Web browser setting ActiveScript settingExamples OS/Browsers Windows XP Professional Internet ExplorerProxy setting ENGLISH JavaScript SettingNetscape Navigator Web browser settingSelect Preference menu from Edit menu on the web browser and then select the item Advanced/Proxies in the Category column. Properly set up your web browsers the proxy server settings according to the local area network environment to which the projector is connected Proxy settingENGLISH Product specificationProduct specification 8-pin modular connector RJ-45 Port specificationLAN port specification Serial port specificationQ Why doesn’t the setting page appear in my web browser? Installation/AccessQ How can I restrict access from the computer Q How can I install several projectors equipped with the Network Unit? Password/LoginQ What should I do when I forget the password Network PIN code? Q How many projectors can I control with multi-control function?Operation Others Q Can I develop a driver to control external serial equipment? Q Why am I not receiving E-mail alert messages?Q Can I control the projector by using the telnet application? Version of the firmware Q Can I update the firmware of the Network Unit?Q What are the rules for IP address assignment? Q What is the MAC address assigned to the Network Unit?Deutschland & Österreich A-key to better communicationsU.S.A Canada