Eizo CG245W Connector Pin Assignment

48 Chapter 7 Reference

Connector Pin Assignment

• DVI-I con nector

12345678

91011 12 13 14 15 16

1920 211718 2223 24

C1 C2

C3 C4

C5

Pin

No.

Signal

Pin

No.

Signal

Pin

No.

Signal

1 T.M.D.S. Data 2- 11 T.M.D.S. Data1/3 Shield 21 NC*

2 T.M.D.S. Data 2+ 12 NC* 22 T.M.D.S. Clock shield

3 T.M.D.S. Data2/4 Shield 13 NC* 23 T.M.D.S. Clock+

4 NC* 14 +5V Power 24 T.M.D.S. Clock-

5 NC* 15 Ground (return for +5V,

Hsync, and Vsync)

C1 Analog Red

6 DDC Clock (SCL) 16 Hot Plug Detec t C2 Analog Green

7 DDC Data (SDA) 17 T.M.D.S. Data0- C3 Analog Blue

8 Analog Vertical Sync 18 T.M.D.S. Data0+ C4 Analog Horizontal Sync

9 T.M.D.S. Data1- 19 T.M.D.S. Data0/5 Shield C5 Analog Ground(analog

R,G,&B return)

10 T.M.D.S. Data1+ 20 NC*

(NC*: No Connection)

• D isplayPort connector

135791113151719

2468101214161820

Pin No.

Signal

Pin No.

Signal

Pin No.

Signal

1 ML Lane3- 8 G round 15 AUX CH+

2 Ground 9 ML Lan e1+ 16 Ground

3 ML Lane3+ 10 ML Lane0- 17 AUX CH-

4 ML Lane2- 11 Ground 18 Hot Plug Detec t

5 Ground 12 ML Lane0+ 19 Return

6 ML Lane2+ 13 CONFIG1 20 DP PWR

7 ML Lane1- 14 CONFIG2

• USB por t

Upstream

Series A connectorSeries B connector

Downstream

Contact No. Signal Remarks

1 VCC Cable power

2 - Data Serial data

3 + Data Serial data

4 Ground Cable ground

Contents

Main [Location of Caution Statement] Notice for this monitor Cleaning To use the monitor comfortably Page CONTENTS 6 Chapter 1 Introduction 1-1. Features CAUTION Be careful of the following points when using the monitor hood. 1-2. Controls and Functions 1-3. Utility Disk 10 1- 4. Basic Operation and Functions Basic operation of menu 1 2 3 12 Functions Page 14 Chapter 2 Adjusting Screen 2-1. Setting Screen Resolution Compatible Resolutions/Frequencies Digital Input (DVI/DisplayPort) Resolution Display Mode Frequency Dot Clock Setting Resolution Page Page Page Page Page 2-5. Displaying Lower Resolutions 2-6. Conguring moving image performance [Overdrive] Chapter 3 Setting Monitor 3-1. Enabling/Disabling Mode Selection [Mode Preset] 3-2. Locking Buttons [Key Lock] 28 3-3. Setting the EIZO Logo Display [Logo] 3-4. Setting Orientation [Orientation] 3-5. Setting Language [Language] Selectable languages 3-6. Setting Range of Frequency [Signal Bandwidth] Page 3-9. Restoring the Default Setting 32 Chapter 4 SelfCalibration 4-1. Executing SelfCalibration [Calibration] 4-2. Checking Calibration Results [Result] 4-3. Setting Calibration Details [Setting] 34 Set the calibration schedule for SelfCalibration. 4. Adjust using or . 5. Press to exit the adjustment. The calibration schedule is set. 36 Chapter 5 Power Saving Function 5-1. Setting the Power Saving [Power Save] Chapter 6 Troubleshooting 38 Page Chapter 7 Reference 7-1. Attaching an Arm Use the screws that hold the monitor and stand together for installation. [Attachment Procedure] 1 Page 7-3. Making Use of USB (Universal Serial Bus) 7-4. Displaying Monitor Information 7-5. Specications Main default settings (factory settings) Chapter 7 Reference Outside Dimensions Unit: mm (inch) 172 Connector Pin Assignment DVI-I con nector D isplayPort connector USB por t 7-6. Glossary Page Page 7-7. Preset Timing About TCO 03 FCC Declaration of Conformity For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity Canadian Notice HinweiseHinweise zur Auswahl des richtigen Schwenkarms fr Ihren Monitor 56 LIMITED WARRANTY LIMITED WARRANTY BEGRENZTE GARANTIE 58 GARANTIE LIMITE GARANTA LIMITADA 60 GARANZIA LIMITATA BEGRNSAD GARANTI 62 64