OPERATING INSTRUCTIONS
150 LT | 15 | 50 | 28 |
4.AUTOMATIC CONTROL
The automatic controls can be fitted with more or fewer func- tions.
The following instructions explain all the possible functions.
4.1Setting the clock
The clock time is shown on the display (AZ).
Switch on the control system switch (S) by turning them from position 0 to I.
Then press and hold down buttons (ZT) and (Q). After the second acoustic signal, the clock time can be set by turning the knob (Z).
Turn right = increase Turn left = reduction Smallest change = 1 minute
After the time has been set, the buttons (ZT) and (Q) can be released again.
4.2Starting
The pan must be in the horizontal position prior to starting, or the power supply must be disconnected.
Programming the cooking time, the starting time and steam condensation in the compartment (or only one func- tion). The
Pressing the button (DT) switches on the programme for the cooking time (flashing nominal value). The desired cooking time is set with the cooking time knob (D) on the display (AD).
Turn right = increase Turn left = reduction Smallest change = 1 minute
The lamp (LD) only lights up when the desired temperature has been reached and the cooking time expires.
Pressing the button (ZT) switches on the programme for the starting point (flashing nominal value).
Set the desired starting time with the starting time knob (Z) on the display (AZ)
Turn right = increase Turn left = reduction Smallest change = 1 minute
The acoustic signal will sound three times and the lamp (LZ) will light up when the starting time has been reached.
Steam condensation (optional) is pre-programmed by press- ing button (V).
4.3Automatic cooking
TT Button, activation of settings
LT | Lamp, cooking temperature |
DT | Button, cooking time |
LD | Lamp, cooking time expires |
ZT | Button, starting time |
LZ | Lamp, starting time |
LR | Lamp, soft settings |
QButton, acoustic signal
RButton, soft
LS Lamp, temperature
AT Display, cooking tempera- ture
TTemperature selection knob AD Display, remaining cooking
time
D Cooking time knob AZ Display, time
Z Starting time knob S Control switch
Fig. 2 Right console
Switching on
Switch on the control switch (S) turn from position 0 to I. This switches on the temperature
0 = Off
I = On
Set the desired cooking temperature (flashing nominal value) with the temperature selection knob (T) on the display (AT).
Turn right = increase Turn left = reduction Smallest change = 1°F
The following
•Cooking temperature
•Cooking time
•Starting time
•Steam condensation
are all activated by pressing the button (TT). The following displays
•Cooking temperature (AT)
•Remaining cooking time (AD)
•Clock time (AZ)
indicate the current value.
The lamp (LT) will continue to flash until the nominal cooking temperature is reached. It then stays on permanently.
When illuminated, this lamp (LV) indicates that steam conden- sation is switched on. When cooking is completed, steam con- densation will start automatically and will remain in operation until the pressure in the appliance has been reduced to nor- mal. The lamp (LV) will flash during the cooling phase.
4.4Shutting down
An acoustic signal sounds when cooking is over. This is acknowledged by pressing the button (Q).
The power supply is then switched off.
All activated functions are subsequently switched off:
•Press the
Lamp (LT) extinguishes.
•Press the cooking time button (DT). Lamp (LD) extinguishes.
•Press the starting time button (ZT). Lamp (LZ) extinguishes.
•Press the button for steam condensation (V). The lamp (LV) will extinguish.
•Switch off the Soft button (R), if this was activated.
•Switch off the control switch (S). Turn from position I to 0.
Lamp (LS) extinguishes.
•Switch off the power isolator (H) (only available as an option).
•Turn from position I to 0.
0 = Off
After cooking has been completed, the control switch (S) is switched off.
Page 6 | 62.9696.01 |