Emerson CF1PW01, CF1WB01, CF1AB01 owner manual Position the ceiling cover trim and the ceiling cover

7.If you have installed the 18” downrod, install the downrod trim and decorative bulb as follows (Figure 5). Slide the decorative trim (grommet-end first) over the downrod and seat the grommet firmly against the motor cover.

Then slide the

decorative bulb (oriented as shown) over the downrod, being certain that the downrod trim seats in the bottom

grommet of the decorative bulb.

18" DOWNROD

GROMMET

DECORATIVE

BULB

GROMMET

DOWNROD

TRIM

GROMMET

MOTOR COVER

Figure 5

12.Use the holes in the square recesses in the motor hub marked with "4" and install the blade assemblies in accordance with Steps 13 or 14.

13.FOUR-BLADE VERSION. Attach one blade assembly to the motor hub using two 10-32 x 5/8" oval head screws (supplied) (Figure 8). Do not tighten completely at this time. Install remaining blade assemblies in the same way. Gently snug all flange screws to the motor hub, working around the hub in a clockwise sequence. Next, securely tighten all flange screws, again working in a clockwise sequence. Failure to follow this procedure could result in fan wobble.

14° FOUR-BLADE FLANGE

8.	Position the ceiling cover trim and the ceiling cover
	over the downrod. Be sure the cover is oriented
	correctly, with the large opening at the top
	(Figure 5).
9.	Reinstall the hanger ball on the downrod (Figure 6)
	as follows. Route the motor leads through the
	hanger ball and slide the hanger ball over the
	downrod. Install the pin through the holes at top of

10-32 x 5/8"

OVAL HEAD SCREWS (2 PER BLADE FLANGE)

Figure 8

MOTOR HUB

the downrod and slide the hanger ball up the

downrod, aligning the ball so the pin is captured in

the groove in the top of the hanger ball. Pull the

hanger ball up tight against the pin and securely

tighten the setscrew in the hanger ball. A loose

setscrew could create fan wobble.

14.TWO-BLADE VERSION. Attach one blade assembly to the motor hub using four 10-32 x 5/8” oval head screws (supplied) (Figure 9). Install the other blade assembly in the same manner. Gently snug all flange screws to the motor hub. Make sure the ends of the flanges are engaged, then securely tighten all flange screws, working in a clockwise sequence.

PIN

HANGER BALL

DOWNROD

Figure 6

10. The fan comes with blue, black and white leads

that are 80” long. Before installing fan, measure

up approximately 6 to 9-inches above the ball/

20° TWO-BLADE FLANGE

10-32 x 5/8"

OVAL HEAD SCREWS (4 PER BLADE FLANGE)

Figure 9

MOTOR HUB

downrod assembly. Cut off excess leads and

strip back insulation 1/2-inch from end of leads.

11. Use five 10-32 x 3/8" pan head screws and flat

washers (supplied) to secure the flange to the

blade (Figure 7). Repeat for the remaining

blade(s).

10-32 x 3/8"

PAN HEAD SCREW (5)

FLAT WASHER (5)

BLADE

BLADE

FLANGE

!WARNING

To reduce the risk of personal injury, do not bend the blade flanges when installing the flanges, balancing the blades or cleaning the fan. Do not insert foreign objects between rotating fan blades.

15.Turn fan assembly over so the bottom is oriented up. Partially install two 8-32 x 1/2” screws (supplied) in the switch housing assembly (Figure 10). Slip the speed control switch chain through the hole in the upper cover trim, then position the cover trim on the switch housing assembly so that the two screws protrude through the key hole slots in the cover trim. Turn the cover trim fully clockwise and then securely tighten the two 8-32 x 1/2” screws.

Figure 7 5