Connecting to a Computer | Energy Speaker Systems LTV46DA manual

Connections and Start of Operation

Connecting to a Computer

You can use the television set as a monitor for the computer. This is possible parallel to television operation. Use a 15-pin D-Sub cable to connect the television set to the computer.

1Plug the cable into the output socket of the graphic board.

2Plug the other end of the cable into the socket [RGB].

3Connect the audio cable according to the colours to the socket [PC Sound] on the television set and the output sockets of the graphic board.

Adjust the settings of the television picture corresponding to the settings for television operation. See “Settings” on Page 16.

English

If the television set does not receive any signal, adjust the output of the computer. For information on how to setup the computer, refer to the corresponding manual of the computer.

Connecting to External Devices with Component Input

You can use the television set to connect DVD recorder/player and set-top-box. Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors.

➣ Connecting to External Devices

1Plug the video cable according into the colours to the output sockets of the external devices.

2Plug the other end of the video cable according to the colours into the Y, Pb, Pr sockets

[AV 3 or AV 4] on the television set.

3Plug the audio cable according to the colours to the audio output sockets of the external devices.

4Plug the other of the audio cable according to the colours into the audio input socket on the television set.

If the external equipment has mono audio output, connect it only to left socket of the audio input/output.

13

Image 15

Energy Speaker Systems LTV46DA manual Connecting to a Computer, Connecting to External Devices with Component Input

Contents

LTV46DA Page Content Reduce Noise Channel Groups Disposal Conformity Scope of Supply Unpacking and SetupSafety Unit Remote control Batteries Mains cable Unpacking and Setup Intended purpose Location Viewing the Control Panels Front ViewRear View Remote Control Connections for TV Reception Connecting to a Device with Scart SocketConnecting to two Devices with Scart Socket Connections and Start of Operation Connecting to a Device without Scart Socket Connecting to the Roof Aerial Connecting Camcorders and Video Games by AV Cable Connecting to Cable ReceptionConnecting to Headphones Connecting Camcorders and Video Games Connecting Camcorders and Video Games by S-Video Cable Connecting Camcorders and Video Games by Scart CableWith the output sockets of the external devices Connecting to a Computer Connecting to External Devices with Component InputAV 3 or AV 4 on the television set Connecting to the Hdmi Connection Connecting the Digital Audio OutputConnecting Several Devices Connecting Mains Cable Inserting the Batteries Connecting HDMI/DVI Cable Setting up for Operation SettingsSwitching On Switching Off Press TuningStarting Automatic Tuning TV Stations Open, Select and Close Menus Use this function to set the channel for individual stations Change channel Set Colour System Set SystemPress . To return to the main menu, press Several times Manual Tuning Fine TuningUse this function to tune the channels manually Press or Select Name Sound SettingsChange Channel Name Unit can record and play back stereo sounds Adjust the settings Press to save the settings Improve Signal QualityUse this function to improve poor signal quality Press Select Install or Use this function to reduce picture noise Reduce NoiseChannel Groups Watch Favourite Channel Set Screen Language Set Aspect RatioSet Wide Screen Format Display if no Wide Screen Signal is Received Set Picture Mode Additional Picture Settings Set Individual Colour ChannelsPress to open the desired menu Set Balance Audio SettingsAdjust Individual Audio Frequencies Set volume Is a registered trademark Adjust Medium and Low Frequencies Enter the time using the key pad Press to save the settings Set Sound SourceSet Time Press Select on or OFF or Set Switch on TimeUse this function to set a time when the unit turns on Set Time by Station Use this function to set a time when the unit turns off Set Switch off TimeAutomatic Switch off Automatic Switch off if no Signal is Received Switch Off if no Key is Pressed Set On-Screen DisplaySet Duration Child Lock Set TransparencyActivate Child Lock Set Characters for Teletext Restore DefaultSettings for the Computer Press Press the mains switch on the back of the unit Set Volume WatchingWatch Current Television Program Press Press repeatedly until you select the desired channel Recall a Favourite ChannelSelect Source Select Input Watch Two Programs at the Same Time PIP Use this function to set the size of the small picture Set Picture-in-Picture SizeSet Picture-in-Picture Position Teletext Show Time Set Picture Mode while WatchingAdjust Picture Size while Watching Still Picture Use this function to set the sound effects Set Sound Effect while WatchingSet Sound while Watching Set Stereo/Mono while Watching Cleaning and Troubleshooting Cannot be displayed. Change the settings in the computer Cast in black and white. Adjust the colour settingsSee chapter Restore Default on Check wether the connecting cable is properly connected to 1360 x Technical specificationsPixel Type Pb/Pr Memo Memo Memo