Cleaning and Troubleshooting | Energy Speaker Systems LTV46DA

Cleaning and Troubleshooting

Cleaning and Troubleshooting

Cleaning

Use a dry cloth to clean the unit. Never use water, cleaning detergents or spray cleaners.

Troubleshooting

If there are problems with the unit, please check the following points before contacting the technical service.

Never open the unit. This may lead to electric shocks and will void the warranty.

No Picture or Sound	Make sure the receiver and the TV set are both connected to the
	mains and switched on.
	Check whether the antenna cable is in proper condition and if it is
	connected to the respective sockets. See chapter “Connecting a
	Satellite Receiver, a Set Top Box or a Video Recorder” on page 9,
	“Connecting to Cable Reception” on page 11 or “Connecting to
	the Roof Aerial” on page 10. If you are using a SCART cable, check
	whether it is properly connected.

Black Screen	Check whether a signal source is selected. See chapter “Select
	Source” on page 36 and “Select Input” on page 36.

Picture OK but no Sound	Check wether the sound is set to mute or if it is turned down.
	See chapter “Set Volume” on page 35.
	Check if the sound is ok on another channel. If this is the case, the
	program is broadcast improperly.

Poor Sound	Switch between stereo and mono sound.
	See chapter “Set Stereo/Mono while Watching” on page 40.

	Check if the channel has been tuned to a station.
No Picture on Some Channels	See chapter “Tuning” on page 17.
	Adjust the fine tuning. See chapter “Fine Tuning” on page 20.

Unstable, Poor Picture	Adjust the fine tuning. See chapter “Fine Tuning” on page 20.
	Check if strong electromagnetic fields, e.g. caused by electric devices
	nearby cause the impairments.

English

41

Image 43

Energy Speaker Systems LTV46DA manual Cleaning and Troubleshooting

Contents

LTV46DA Page Content Reduce Noise Channel Groups Disposal Conformity Scope of Supply Unpacking and SetupSafety Unit Remote control Batteries Mains cable Unpacking and Setup Intended purpose Location Front View Viewing the Control PanelsRear View Remote Control Connections for TV Reception Connecting to a Device with Scart SocketConnecting to two Devices with Scart Socket Connections and Start of Operation Connecting to a Device without Scart Socket Connecting to the Roof Aerial Connecting Camcorders and Video Games by AV Cable Connecting to Cable ReceptionConnecting to Headphones Connecting Camcorders and Video Games Connecting Camcorders and Video Games by Scart Cable Connecting Camcorders and Video Games by S-Video CableWith the output sockets of the external devices Connecting to External Devices with Component Input Connecting to a ComputerAV 3 or AV 4 on the television set Connecting to the Hdmi Connection Connecting the Digital Audio OutputConnecting Several Devices Connecting Mains Cable Inserting the Batteries Connecting HDMI/DVI Cable Setting up for Operation SettingsSwitching On Switching Off Press TuningStarting Automatic Tuning TV Stations Open, Select and Close Menus Use this function to set the channel for individual stations Change channel Set System Set Colour SystemPress . To return to the main menu, press Several times Fine Tuning Manual TuningUse this function to tune the channels manually Press or Select Name Sound SettingsChange Channel Name Unit can record and play back stereo sounds Adjust the settings Press to save the settings Improve Signal QualityUse this function to improve poor signal quality Press Select Install or Use this function to reduce picture noise Reduce NoiseChannel Groups Watch Favourite Channel Set Aspect Ratio Set Screen LanguageSet Wide Screen Format Display if no Wide Screen Signal is Received Set Picture Mode Set Individual Colour Channels Additional Picture SettingsPress to open the desired menu Set Balance Audio SettingsAdjust Individual Audio Frequencies Set volume Is a registered trademark Adjust Medium and Low Frequencies Set Sound Source Enter the time using the key pad Press to save the settingsSet Time Press Select on or OFF or Set Switch on TimeUse this function to set a time when the unit turns on Set Time by Station Use this function to set a time when the unit turns off Set Switch off TimeAutomatic Switch off Automatic Switch off if no Signal is Received Set On-Screen Display Switch Off if no Key is PressedSet Duration Set Transparency Child LockActivate Child Lock Set Characters for Teletext Restore DefaultSettings for the Computer Press Press the mains switch on the back of the unit Watching Set VolumeWatch Current Television Program Press Press repeatedly until you select the desired channel Recall a Favourite ChannelSelect Source Select Input Watch Two Programs at the Same Time PIP Use this function to set the size of the small picture Set Picture-in-Picture SizeSet Picture-in-Picture Position Teletext Show Time Set Picture Mode while WatchingAdjust Picture Size while Watching Still Picture Use this function to set the sound effects Set Sound Effect while WatchingSet Sound while Watching Set Stereo/Mono while Watching Cleaning and Troubleshooting Cannot be displayed. Change the settings in the computer Cast in black and white. Adjust the colour settingsSee chapter Restore Default on Check wether the connecting cable is properly connected to 1360 x Technical specificationsPixel Type Pb/Pr Memo Memo Memo