035-17233-000-C-0702

 

CONDENSERSECTION

GAUGELINE

EVAPORATOR

ACCESS

SECTION

DOTPLUG (Forpressure dropreading)

40-3/8"

SUPPLY

AIR

 

RETURN

5-1/2"

AIR

 

COMPRESSOR

OUTDOOR

ACCESS

AIR

 

SUPPLYAIR

 

ACCESS

 

FILTER

ACCESS

1"NPTFEMALE COND.DRAIN CONNECTION

40-1/2"

18-5/8"

REAR

VIEW

 

 

27-3/4"

RETURNAIR 5-1/8"

OUTDOORAIR

ACCESS

COMPARTMENT

 

 

ACCESS

 

 

28-5/8"(15Tons)

 

 

39-5/8"(20Tons)

FIGURE 12 : UNIT DIMENSIONS DHE/DHG180 & 240 (REAR VIEW)

NOTE: A 1” clearance must be provided between any com- bustible material and the supply air ductwork for a distance of 3 feet from the unit.

NOTE: The products of combustion must not be allowed to accumulate within a confined space and recirculate.

NOTE: Locate unit so that the vent air outlet hood is at least:

Three (3) feet above any force air inlet located within 10 horizontal feet (excluding those integral to the unit).

Four (4) feet below, 4 horizontal feet from, or 1 foot above any door or gravity air inlet into the building.

Four (4) feet from electric and gas meters, regulators and relief equipment

NOTE: All entry holes should be field sealed to prevent rain water entry into building

Duct Covers - Units are shipped with the bottom duct open- ings covered. An accessory flange kit is available for con- necting side ducts.

For bottom duct applications:

1.Remove the side panels from the supply and return air compartments.

2.Remove and discard the bottom duct covers. (Duct openings are closed with sheet metal covers except when the unit includes a power exhaust option. The cov- ering consists of a heavy black paper composition.)

TABLE 10: UTILITIES ENTRY

HOLE

OPENING SIZE

USED FOR

(DIA.)

 

 

 

 

 

 

 

A

1-1/8” KO

Control Wiring

Front

 

 

3/4” NPS (Fem.)

Bottom

 

 

 

 

 

 

B

3-5/8” KO

Power Wiring

Front

 

 

3” NPS (Fem.)

Bottom

 

 

 

 

 

 

C

2-3/8” KO

Gas Piping (Front)1

D

1-11/16” Hole

Gas Pipping (Bottom)1,2

11” Gas Piping MPT Required.

2Opening in the bottom to the unit can be located by the side in the insulation.

3.Replace the side supply and return air compartment pan- els.

For side duct applications:

1.Replace the side panels on the supply and return air compartments with the accessory flange kit panels.

2.Connect ductwork to the duct flanges on the rear of the unit.

Unitary Products

15

Page 15
Image 15
Energy Tech Laboratories DHG240 installation instructions Unit Dimensions DHE/DHG180 & 240 Rear View, Utilities Entry

DHG180, DHG240 specifications

Energy Tech Laboratories has made significant strides in the realm of energy efficiency and renewable technologies with the introduction of their innovative models, the DHG240 and DHG180. These advanced devices are designed to optimize energy consumption, minimize environmental impact, and enhance overall energy management.

The DHG240 model stands out with its high-capacity performance, delivering a robust output of 240 kW. This unit is ideal for large facilities and industrial applications, where energy demands are high. One of its main features is its advanced algorithm for energy distribution, which allows for optimal load balancing across various operational units. This ensures that energy is used efficiently, reducing waste and lowering operational costs.

Similarly, the DHG180 is designed for medium-sized operations, providing an output of 180 kW. It offers an effective solution for businesses seeking to improve energy efficiency without the excessive overhead costs typically associated with larger systems. The DHG180 incorporates state-of-the-art monitoring systems that provide real-time data on energy consumption, allowing operators to make informed decisions and adjust settings as needed.

Both models integrate cutting-edge technologies such as smart grid capabilities and renewable energy sources. They are equipped to handle integration with solar panels and wind turbines, enabling facilities to harness clean energy and reduce reliance on fossil fuels. This feature not only contributes to sustainability goals but also provides a buffer against fluctuating energy prices.

The design of both the DHG240 and DHG180 prioritizes durability and reliability. They are constructed from high-quality materials that withstand harsh operational conditions, ensuring a long lifespan and reduced maintenance costs. Furthermore, these systems are compliant with various energy efficiency standards, making them a responsible choice for environmentally conscious businesses.

User-friendliness is another hallmark of these devices. An intuitive interface allows operators to easily monitor and control energy usage, while remote access compatibility enables management from off-site locations. This flexibility is crucial in today’s fast-paced business environment.

In conclusion, Energy Tech Laboratories’ DHG240 and DHG180 models represent the forefront of energy technology. By delivering high performance, integrating renewable solutions, and prioritizing ease of use, these units empower businesses to achieve their energy efficiency goals while promoting sustainability. Whether for large industries or medium-sized enterprises, these systems are engineered to meet the dynamic needs of modern energy management.