Hardware Installation | Enterasys Networks C2K122-24 instruction

3

Hardware Installation

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Important Notice

Read the Release Notes shipped with the switch to check for any exceptions to the supported features and operation documented in this guide.

This chapter provides instructions to install the C2K122‐24. Follow the order of the sections listed below to correctly install the switch.

For information about...	Refer to page...

Considerations Prior to Installation	3-2

Required Tools	3-2

Unpacking the Switch	3-2

Installing Optional XFPs	3-3

Installing the Switch on a Flat Surface	3-5

Connecting High-Speed Stacking Cables	3-9

Configuring Switches in a Stack	3-10

Connecting AC and RPS Power	3-13

Connecting to Console Port for Local Management	3-16

Connecting to the Network	3-20

Completing the Installation	3-26

SecureStack C2 Installation Guide 3-1

Image 31

Enterasys Networks C2K122-24 manual Hardware Installation

Contents

Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide How to Use This GuideWho Should Use This Guide For Refer to Related Documents Following conventions are used in this guide Conventions Used in This Guide Conventions Used in This Guide Xviii About This Guide Overview Introduction C2K122-24 C2K122-24 Stackable Switch Front Description of XFPs Redundant Power Supply CapabilityConnectivity High-Speed Stack Connections Management Lanview Diagnostic LEDsSwitch Configuration Using WebView Switch Configuration Using CLI Commands Support@enterasys.com Getting Help Getting Help Introduction 10BASE-TX Network Network Requirements 1000BASE-T Network 100BASE-TX Network10GBASE-XX Network Type Max. Length Connector Recommended Cable Types and Specifications 10GBASE-XX Network Network Requirements Hardware Installation Required Tools Considerations Prior to InstallationUnpacking the Switch Contents of Switch Carton Quantity Preparation Installing Optional XFPs Removing the XFP Installing the XFP Installing the Rubber Feet Installing the Switch on a Flat Surface Chassis Bottom, Rubber Feet Placement Guidelines for Installation Area Guidelines for Switch Installation on Flat Surface Rack Mounting the Switch Attaching Brackets and Installing in Rack Guidelines for Rackmount Installation Fastening the Switch to the Rack Connecting High-Speed Stacking Cables High-Speed Stacking Cable Connections Configuring Switches in a Stack About SecureStack C2 Switch Operation in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing Stacks AC Power Connecting AC and RPS Power Switch Rear View Stack Initialization Overview RPS Power What Is Needed Connecting to Console Port for Local Management Parameter Setting Connecting to an IBM or Compatible Device 10 Connecting a VT Series Terminal Connecting to a VT Series Terminal 11 Connecting to a Modem Connecting to a Modem Connecting UTP Cables Connecting to the Network 13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the Installation Troubleshooting C2K122-24 Lanview LEDs Using Lanview Color State Recommended Action Lanview LEDs RPS Refer to the SecureStack C2 Configuration Guide for proper Troubleshooting Checklist Refer to the SecureStack C2 Configuration Guide for the IP Password Reset Switch Using the Password Reset Switch Using the Password Reset Switch Troubleshooting Specifications Environmental Switch SpecificationsTable A-1 Switch Specifications C2K122-24 Physical Supported XFP Transceiver Interface Options SpecificationTable A-2 Supported XFP Transceivers Regulatory Compliance Console Port Pinout AssignmentsTable A-5 Compliance Standards Regulatory Compliance Numerics Index Installation of 3-3specifications for A-3