Enterasys Networks RBT-4102 COMPLIANCES

Compliances

ii

COMPLIANCES

RBT-4102, RBT-4102-BG, and RBT-4102-EU

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

• Consult the dealer or an experienced radio/TV technician for help

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment. This

device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to

channels 1 through 11.

IMPORTANT NOTE:

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance

of 70 centimeters (27.5 inches) between the radiator and your body. This transmitter

must not be co-located or operating in conjunction with any other antenna or transmitter.

Contents

Main Page i NOTICE ii COMPLIANCES RBT-4102, RBT-4102-BG, and RBT-4102-EU Federal Communication Commission Interference Statement IMPORTANT NOTE: FCC Radiation Exposure Statement iii Wireless 5 GHz Band Statements: Wireless 4.9 GHz Band Statement: Industry Canada - Class B RBT-4102-EU iv EC Conformance Declaration Countries of Operation & Conditions of Use in the European Community v Operation Using 5 GHz Channels in the European Community Countries of Operation & Conditions of Use in the Asia, Pacific, and Middle East Communities vi Operation Using 5 GHz Channels in the Asia, Pacific, and Middle East Community vii RBT-4102C and RBT-4102C-EU Federal Communication Commission Interference Statement IMPORTANT NOTE: FCC Radiation Exposure Statement Wireless 5 GHz Band Statements: viii RBT-4102C-EU Australia/New Zealand AS/NZS 4771 Japan Telec Approval EC Conformance Declaration ix Countries of Operation & Conditions of Use in the European Community x Operation Using 5 GHz Channels in the European Community Countries of Operation & Conditions of Use in the Asia, Pacific, and Middle East Communities xi Operation Using 5 GHz Channels in the Asia, Pacific, and Middle East Community EC-Konformittserklrung xii DECLARATION OF CONFORMITY IN LANGUAGES OF THE EUROPEAN COMMUNITY xiii xiv SAFETY COMPLIANCE Power Cord Safety Page Page xvii ENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENT xviii xix xx xxi Page xxiii Table of Contents Preface xxiv xxv Preface Purpose Intended Audience Associated Documents xxvi Getting Help 1-1 Chapter 1: Introduction Introduction 1-2 Package Checklist Hardware Description Hardware Description 1-3 Rear Panel Introduction 1-4 Component Description Antennas External Antenna Connectors LED Indicators Hardware Description 1-5 Security Slot Console Port Page Page Page 2-1 Chapter 2: Hardware Installation Hardware Installation 2-2 2-3 Page 3-1 Chapter 3: Access Point Configuration Using the CLI Required Connections 3-2 Logging In Using the CLI 3-3 3-4 Using the CLI 3-5 3-6 Using Web Management 3-7 3-8 3-9 3-10 3-11 Page Page 3-14 4-1 Chapter 4: Network Configuration Network Configuration 4-2 Network Topologies Ad Hoc Wireless LAN (no Access Point) Network Topologies 4-3 Infrastructure Wireless LAN Network Configuration 4-4 Infrastructure Wireless LAN for Roaming Wireless PCs Network Topologies 4-5 Infrastructure Wireless Bridge Page A-1 Appendix A: Troubleshooting Diagnosing Access Point Indicators Page B-1 Appendix B: Cables and Pinouts Twisted-Pair Cable Assignments Cables and Pinouts B-2 10/100BASE-TX Pin Assignments Twisted-Pair Cable Assignments B-3 Straight-Through Wiring Crossover Wiring EIA/TIA568B RJ-45 Wiring Standard 10/100BASE-TXStraight-through Cable EIA/TIA568B RJ-45 Wiring Standard 10/100BASE-TXCrossover Cable Cables and Pinouts Console Port Pin Assignments Wiring Map for Serial Cable C-1 Appendix C: Specifications General Specifications Maximum Channels 802.11a 802.11b/g Modulation Type Network Configuration Operating Frequency AC Power Adapter Unit Power Supply Page C-4 Compliances Radio Signal Certification Safety Standards Sensitivity Sensitivity C-6 Transmit Power Operating Range C-7 Operating Range C-8 External Antennas External Antennas C-9 Page Index-1 Index A B C D