Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks RBT-8110 manual Example 2 Deployment Site Has No DHCP and No DNS

Models: RBT-8110

1 36

Download 36 pages 33.93 Kb

Page 31

Wireless Switch Configuration Tasks

Example 2: Deployment Site Has No DHCP and No DNS

The deployment site in this example does not have a DHCP server or a local DNS server. Therefore, IP and DNS information must be statically configured. Because no DNS server is available, an IP alias is configured to map the RASM server’s IP address to the well‐known hostname wlan‐config‐srv.

1.Configure a VLAN:

RBT-8110#set vlan 1 port 1

2.Configure an IP interface on the VLAN.

RBT-8110#set interface 1 ip 192.168.1.252 255.255.255.0

3.Configure a default route through the local gateway:

RBT-8110#set ip route default 192.168.1.1 1

4.Configure the default DNS domain name:

RBT-8110#set ip dns domain example.com

5.Configure an IP alias to map the RASM server IP address to the well‐known name wlan‐config‐srv:

RBT-8110#set ip alias wlan-config-srv 172.16.22.84

6.Enable the auto‐config option:

RBT-8110#set auto-config enable

7.Save the configuration changes:

RBT-8110#save config

8.Reset the switch by using one of the following methods:

•Enter the following command:

RBT-8110#reset system

•Turn the power off to the switch, and then turn the power back on.

Example 3: Deployment Site Has DNS But No DHCP

The deployment site in this example does not have a DHCP server but does have a local DNS server. The configuration is similar to Example 1, but includes DNS configuration information instead of an IP alias.

1.Configure a VLAN:

RBT-8110#set vlan 1 port 1

2.Configure an IP interface on the VLAN.

RBT-8110#set interface 1 ip 192.168.1.252 255.255.255.0

3.Configure a default route through the local gateway:

RBT-8110#set ip route default 192.168.1.1 0

4.Configure the default DNS domain name:

RBT-8110#set ip dns domain example.com

5.Configure DNS server information:

RBT-8110#set ip dns server 192.168.11.2

RBT-8110 Wireless Switch Installation Guide 3-7

Image 31

Enterasys Networks RBT-8110 manual Example 2 Deployment Site Has No DHCP and No DNS

Contents

Wireless Networking RBT-8110 Wireless Switch Installation GuideRoamAbout Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Federal Communications Commission FCC Notice Safety and EMC RequirementsProduct Safety Regulatory Compliance InformationHazardous Substances Electromagnetic Compatibility EMCCompatibilidad Electromágnetica EMC Elektro-magnetische Kompatibilität EMCManufacturer’s Name Enterasys Networks, Inc VCCI NoticeBSMI EMC Statement - Taiwan Declaration of ConformityYou and Enterasys agree as follows Enterasys Networks, Inc Firmware License AgreementBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the Program is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party 10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law viii Chapter 3 Configuration ContentsChapter 1 RBT-8110 Wireless Switch Overview Chapter 2 InstallationPage Conventions Used in This Guide About This GuideIntended Audience Associated DocumentsGetting Help Figure 1-1 Front Panel Controls and Indicators RBT-8110 Wireless Switch OverviewKit Contents Front Panel Controls and IndicatorsFunction Table 1-2 LED Indicator StatusTable 1-1 Control Button Functions ButtonTable 1-4 Physical Specifications Power SupplyPhysical Specifications Table 1-3 Power Supply SpecificationsDescription Environmental SpecificationsTable 1-5 Environmental Specifications ParameterSafety Information InstallationRisk of explosion if battery is replaced by incorrect type Warning Refer to the following information 2-4 Installation Rack MountingFront Mount Figure 2-1 Rack Mounting-Front MountFigure 2-2 Rack Mounting-Mid-Mount Mid-MountRack Mounting 2-6 InstallationUsing the CLI quickstart Command ConfigurationPre-Configuration Tasks Wireless Switch Configuration TasksDirectly connected access points Distributed access points quickstart Command Procedure RBT-8110# set ip telnet server enable 6. Optionally, enable Telnet7. Verify the configuration changes 8. Save the configuration changesPreconfigure the Wireless Switch in RASM Configuring RoamAbout Wireless Switches Using RASMExample 1 Deployment Site Has DHCP and Local DNS Stage the Wireless SwitchPreparing the Switch Preparing the NetworkExample 3 Deployment Site Has DNS But No DHCP Example 2 Deployment Site Has No DHCP and No DNSPage Preparing the Network for Distributed Access Points 3-10 Configuration Preparing the Network for Distributed Access PointsIndex