Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks RBT-8110 manual Index

Models: RBT-8110

1 36

Download 36 pages 33.93 Kb

Page 35

A

access points, distributed 3-9Associated documents xi

B

Back panel 1-3

BSMI EMC Statement iv

C

Class A ITE Notice ii

Configuring 3-1

Conventions used xi

D

Distributed access points, preparing for 3-9

Documentation xi

E

Electromagnetic Compatibility Notice iii

Enterasys

Class A ITE Notice ii EMC Notice iii

EMSI Statement - Taiwan iv FCC Notice ii

Firmware License Agreement v Product Safety notice ii VCCI Notice iv

F

FCC Notice ii

Firmware License Agreement v Front panel 1-1

G

Getting help xii

H

Help xii

I

Indicators 1-1

Industry Canada Notice ii Input voltage 1-3Install

rack 2-1Intended audience xi

K

Kit contents 1-1

N

Notices

BSMI EMC iv

Class A ITE ii

EMC iii

FCC ii

General ii

Industry Canada ii

Product Safety ii

VCCI iv

O

Output voltage 1-3

Overview 1-1

P

Power supply 1-3

Pre-configuration 3-1

Q

quickstart command, using 3-1

Index

R

Rack installation 2-1Rack Mount

front mount 2-4Rack mount

mid-mount 2-5

RASM, remote configuration 3-5Regulatory compliance

FCC Notice ii Remote configuration 3-5

example with DHCP and DNS 3-6example with DHCP, local DNS 3-8example with DNS, no DHCP 3-7example with no DHCP or DNS 3-7

Requirements environmental 1-4physical 1-3

S

Safety information 2-1Specifications

environmental 1-4physical 1-3

T

Technical support xii

V

VCCI Notice iv Voltage

input 1-3output 1-3

Index-1

Image 35

Enterasys Networks RBT-8110 manual Index

Contents

RoamAbout RBT-8110 Wireless Switch Installation GuideWireless Networking Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Federal Communications Commission FCC Notice Safety and EMC RequirementsProduct Safety Regulatory Compliance InformationHazardous Substances Electromagnetic Compatibility EMCCompatibilidad Electromágnetica EMC Elektro-magnetische Kompatibilität EMCManufacturer’s Name Enterasys Networks, Inc VCCI NoticeBSMI EMC Statement - Taiwan Declaration of ConformityYou and Enterasys agree as follows Enterasys Networks, Inc Firmware License AgreementBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the Program is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party 10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law viii Chapter 3 Configuration ContentsChapter 1 RBT-8110 Wireless Switch Overview Chapter 2 InstallationPage Conventions Used in This Guide About This GuideIntended Audience Associated DocumentsGetting Help Figure 1-1 Front Panel Controls and Indicators RBT-8110 Wireless Switch OverviewKit Contents Front Panel Controls and IndicatorsFunction Table 1-2 LED Indicator StatusTable 1-1 Control Button Functions ButtonTable 1-4 Physical Specifications Power SupplyPhysical Specifications Table 1-3 Power Supply SpecificationsDescription Environmental SpecificationsTable 1-5 Environmental Specifications ParameterSafety Information InstallationRisk of explosion if battery is replaced by incorrect type Warning Refer to the following information 2-4 Installation Rack MountingFront Mount Figure 2-1 Rack Mounting-Front MountFigure 2-2 Rack Mounting-Mid-Mount Mid-MountRack Mounting 2-6 InstallationUsing the CLI quickstart Command ConfigurationPre-Configuration Tasks Wireless Switch Configuration TasksDirectly connected access points Distributed access points quickstart Command Procedure RBT-8110# set ip telnet server enable 6. Optionally, enable Telnet7. Verify the configuration changes 8. Save the configuration changesPreconfigure the Wireless Switch in RASM Configuring RoamAbout Wireless Switches Using RASMExample 1 Deployment Site Has DHCP and Local DNS Stage the Wireless SwitchPreparing the Switch Preparing the NetworkExample 3 Deployment Site Has DNS But No DHCP Example 2 Deployment Site Has No DHCP and No DNSPage Preparing the Network for Distributed Access Points 3-10 Configuration Preparing the Network for Distributed Access PointsIndex