Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks RBT-8110 manual

Models: RBT-8110

1 36

Download 36 pages 33.93 Kb

Page 32

Wireless Switch Configuration Tasks

6.Enable the MSS DNS client:

RBT-8110#set ip dns server enable

7.Enable the auto‐config option:

RBT-8110#set auto-config enable

8.Save the configuration changes:

RBT-8110#save config

9.Reset the switch by using one of the following methods:

•Enter the following command:

RBT-8110#reset system

•Turn the power off to the switch, and then turn the power back on.

Example 4: Deployment Site Has DHCP But Local DNS Domain Differs From Corporate DNS Domain

The deployment site in this example has a DHCP server, so the switch’s DHCP client is enabled. Static IP address and default router (gateway) information are not required. The site also has a local DNS server. However, the local DNS domain name is different from the corporate DNS domain name where the RASM server is located. The static DNS configuration on the switch overrides the DNS configuration from the DHCP server.

1.Configure a VLAN:

RBT-8110#set vlan 1 port 1

2.Enable the DHCP client on VLAN 1:

RBT-8110#set interface 1 ip dhcp-client enable

3.Configure the default DNS domain name:

RBT-8110#set ip dns domain customer.com

4.Configure DNS server information:

RBT-8110#set ip dns server 192.168.11.2

5.Enable the MSS DNS client:

RBT-8110#set ip dns server enable

6.Enable the auto‐config option:

RBT-8110#set auto-config enable

7.Save the configuration changes:

RBT-8110#save config

8.Reset the switch by using one of the following methods:

•Enter the following command:

RBT-8110#reset system

•Turn the power off to the switch, and then turn the power back on.

3-8 Configuration

Image 32

Enterasys Networks RBT-8110 manual

Contents

RoamAbout RBT-8110 Wireless Switch Installation GuideWireless Networking Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Safety and EMC Requirements Product SafetyRegulatory Compliance Information Federal Communications Commission FCC NoticeElectromagnetic Compatibility EMC Compatibilidad Electromágnetica EMCElektro-magnetische Kompatibilität EMC Hazardous SubstancesVCCI Notice BSMI EMC Statement - TaiwanDeclaration of Conformity Manufacturer’s Name Enterasys Networks, IncEnterasys Networks, Inc Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCTCAREFULLY READ THIS LICENSE AGREEMENT You and Enterasys agree as follows4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the Program is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party 10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law viii Contents Chapter 1 RBT-8110 Wireless Switch OverviewChapter 2 Installation Chapter 3 ConfigurationPage About This Guide Intended AudienceAssociated Documents Conventions Used in This GuideGetting Help RBT-8110 Wireless Switch Overview Kit ContentsFront Panel Controls and Indicators Figure 1-1 Front Panel Controls and IndicatorsTable 1-2 LED Indicator Status Table 1-1 Control Button FunctionsButton FunctionPower Supply Physical SpecificationsTable 1-3 Power Supply Specifications Table 1-4 Physical SpecificationsEnvironmental Specifications Table 1-5 Environmental SpecificationsParameter DescriptionInstallation Safety InformationRisk of explosion if battery is replaced by incorrect type Warning Refer to the following information Rack Mounting Front MountFigure 2-1 Rack Mounting-Front Mount 2-4 InstallationMid-Mount Figure 2-2 Rack Mounting-Mid-Mount2-6 Installation Rack MountingConfiguration Pre-Configuration TasksWireless Switch Configuration Tasks Using the CLI quickstart CommandDirectly connected access points Distributed access points quickstart Command Procedure 6. Optionally, enable Telnet 7. Verify the configuration changes8. Save the configuration changes RBT-8110# set ip telnet server enableConfiguring RoamAbout Wireless Switches Using RASM Preconfigure the Wireless Switch in RASMStage the Wireless Switch Preparing the SwitchPreparing the Network Example 1 Deployment Site Has DHCP and Local DNSExample 2 Deployment Site Has No DHCP and No DNS Example 3 Deployment Site Has DNS But No DHCPPage Preparing the Network for Distributed Access Points Preparing the Network for Distributed Access Points 3-10 ConfigurationIndex