Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks RBT-8110 manual 1 Control Button Functions, 2 LED Indicator Status

Models: RBT-8110

1 36

Download 36 pages 33.93 Kb

Page 16

Table 1-1 Control Button Functions

Running H/F 2

Table 1-1 Control Button Functions

	Button	Function

	Power	Toggles the system power on/off.

	Reset	Performs a soft system re-boot.

	Table 1-2 LED Indicator Status

	LED	Function

	NIC1 activity	• A continuous amber light indicates a link between the system and the network to which it
	NIC2 activity	is connected.
	NIC2 activity	• A blinking amber light indicates network activity.
		• A blinking amber light indicates network activity.

	Status/Power	• A continuous blue light indicates that the system has power applied to it.
		• No light indicates that the system does not have power applied to it.

	Hard drive	• A continuous blue light indicates a hard drive disk fault.
	disk status	• A random blinking blue light indicates hard drive activity.

1-2 RBT-8110 Wireless Switch Overview

Image 16

Enterasys Networks RBT-8110 manual 1 Control Button Functions, 2 LED Indicator Status

Contents

Wireless Networking RBT-8110 Wireless Switch Installation GuideRoamAbout Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Safety and EMC Requirements Product SafetyRegulatory Compliance Information Federal Communications Commission FCC NoticeElectromagnetic Compatibility EMC Compatibilidad Electromágnetica EMCElektro-magnetische Kompatibilität EMC Hazardous SubstancesVCCI Notice BSMI EMC Statement - TaiwanDeclaration of Conformity Manufacturer’s Name Enterasys Networks, IncEnterasys Networks, Inc Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCTCAREFULLY READ THIS LICENSE AGREEMENT You and Enterasys agree as follows4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the Program is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party 10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law viii Contents Chapter 1 RBT-8110 Wireless Switch OverviewChapter 2 Installation Chapter 3 ConfigurationPage About This Guide Intended AudienceAssociated Documents Conventions Used in This GuideGetting Help RBT-8110 Wireless Switch Overview Kit ContentsFront Panel Controls and Indicators Figure 1-1 Front Panel Controls and IndicatorsTable 1-2 LED Indicator Status Table 1-1 Control Button FunctionsButton FunctionPower Supply Physical SpecificationsTable 1-3 Power Supply Specifications Table 1-4 Physical SpecificationsEnvironmental Specifications Table 1-5 Environmental SpecificationsParameter DescriptionInstallation Safety InformationRisk of explosion if battery is replaced by incorrect type Warning Refer to the following information Rack Mounting Front MountFigure 2-1 Rack Mounting-Front Mount 2-4 InstallationMid-Mount Figure 2-2 Rack Mounting-Mid-Mount2-6 Installation Rack MountingConfiguration Pre-Configuration TasksWireless Switch Configuration Tasks Using the CLI quickstart CommandDirectly connected access points Distributed access points quickstart Command Procedure 6. Optionally, enable Telnet 7. Verify the configuration changes8. Save the configuration changes RBT-8110# set ip telnet server enableConfiguring RoamAbout Wireless Switches Using RASM Preconfigure the Wireless Switch in RASMStage the Wireless Switch Preparing the SwitchPreparing the Network Example 1 Deployment Site Has DHCP and Local DNSExample 2 Deployment Site Has No DHCP and No DNS Example 3 Deployment Site Has DNS But No DHCPPage Preparing the Network for Distributed Access Points Preparing the Network for Distributed Access Points 3-10 ConfigurationIndex