Manuals / Brands / Computer Equipment / Printer / Epson / Computer Equipment / Printer

Epson 440 2.2.2.4 Timer Circuit, 2.2.2.5 DRAM Control

1 160

Download 160 pages, 2.58 Mb

EPSON Stylus Color 600

Rev. A

2-2

6

2.2.2.4 Timer Circuit

The lithium battery is mounted on t he C200 m ain board and calculates how long the printer is not in used.

The timer IC(IC10) starts counting with oscillation motivated by the CR3 using this battery as a power

source. The figure below shows connection of the Timer circui t.

The followings explain about operation of this circuit.

When the printer is on, power is supplied to the Timer I C by applying +5V quickly through

the D4.

This power is also used for the power to oscillate the outer CR3. The oscillation wave form is

input to XIN terminal.

Since the oscillation wave form of CR1 is analog waveform, it is processed into the

pulse form in the Timer IC.

When the printer is turned on, the Timer I C out puts power off time as serial data to the gate

array.

Once the printer is turned off, 3VDC of BAT1(lithium batt ery) is supplied as power source for

the Timer IC through D1.

Since +5V at the power on is higher than +3V of the li thium battery, the power is not being

consumed from the lithium bat t ery.

2.2.2.5 DRAM Control

In the Dynamic RAM control, output and f ormation of CAS and RAS control signals become nec essary

in addition to the output of CS signal. T he CPU TMP95C061AF not only controls that but also perform

the output of CS signal of P-ROM. Ref resh timing is performed in the CAS Bef ore RAS.

TCE

TIO

TCLK

TDATA

125

122

123

126

CS

/SCK

SIO

VDD

XOUT

XIN

VSS

CR3

+5V

BAT1

D1

D4

+5V

E05B43(IC2)

S-3510ANFJ

(IC10)

8

2

3

4

1

6

7

Figure 2-23. Timer Circuit Block Diagram

Contents

Main NOTICE PRECAUTIONS WARNING CAUTION WARNING CAUTION PREFACE Page Page Chapter 1 Product Descriptions 1.1 Features 1.2 Specifications 1.2.1 Printing Specification Page Note) *1: Each typeface has four different font style; Normal, Bold, Italic and Bold-Italic. 1.2.2 Paper Specification 1.2.2.1 Cut Sheet 1.2.2.2 Transparency Film / Glossy Paper 1.2.2.3 Envelope 1.2.2.4 Index Card 1.2.3 Adjust Lever Settings (PG adjust lever) Rev. A 1- 1.2.4 Printable Area 1.2.4.1 Cut Sheet 1.2.4.2 Envelope 1.2.5 Environmental Condition 1.2.6 Ink Cartridge Specifications 1.2.6.1 Black Ink Cartridge Rev. A 1-11 1.2.6.2 Color Ink Cartridge Note) 1.2.7 Physical Specification 1.2.8 Electric Specification 1.2.9 Reliability 1.2.10 Safety Approvals 1.2.11 Acoustic Noise 1.2.12 CE Marking 1.2.13 Printer Language and Emulation Page 1.3 Interface 1.3.1 Parallel Interface (Forward Channel) Note) I/O refers to the direction of signal flow from the printers point of view. 1.3.2 Parallel Interface (Reverse Channel) Note) The printer sends following device ID string when it is requested. Note) I/O refers to the direction of signal flow from the printers point of view. Note) *: Rise and fall time of every output signals. **: Rise and fall time of every input signals. 1.3.2.1 Prevention Hosts from Data Transfer time-out 1.3.3 Serial Interface Rev. A 1-21 1.4 Control Panel 1.4.1 Indicators 1.4.2 Panel Functions 1.4.3 Printer Condition and Panel Status 1.5 Error Status 1.5.1 Ink Out Never use the ink cartridge once taken out from the printer. 1.5.2 Paper Out 1.5.3 Paper Jam 1.5.4 No Ink-Cartridge Error 1.5.5 Maintenance Request 1.5.6 Fatal Errors 1.6 Printer Initialization 1.6.1 Initialization Settings Rev. A 1-2 1.7 Main Components 1.7.1 Printer Mechanism 1.7.2 C200 MAIN Board Figure 1-13. Exterior view of C200 Main Board Rev. A 1-2 1.7.3 C206 PSB/PSE Board 1.7.4 C206 PNL Board Chapter 2 Operating Principles 2-17 2.1 OVERVIEW 2.1.1 Printer Mechanism 2.1.1.1 Printing Mechanism Page 2.1.1.1.2 Printing Method Note1: Note1) Note3: Note2: Nozzle No.#9 Nozzle No.#4 Particular line(Completed line) 360-dpi Condition: 360-dpi printing Nozzle: Total 10 nozzle/each color #1 #2 #3 #4 #5 #6 Page Rev. A 2- 2.1.1.2 Carriage Mechanism Rotor *Note 1): B A /A /B C200 MAIN Board Connecter CN6(CN7) Page Rev. A 2- 2.1.1.2.1 Platen Gap Adjust Mechanism and Parallel adjustment Mechanism Rev. A 2-11 2.1.1.3 Paper Feed Mechanism and Pump Mechanism Page Page 2.1.1.4 Ink System 2.1.1.4.1 Pump, Carriage Lock, Head Cleaner Mechanism CW Rotation CCW Rotation Tube pressured Tube released 2.1.1.4.2 Cap Mechanism AB 2.2 Electrical Circuit Operating Principles 2.2.1 C206 PSB/PSE Power Board AC100V Rev. A 2-21 2.2.2 C200 Main Board Page Rev. A 2-2 2.2.2.1 Reset Circuits 2.2.2.2 Sensor Circuits E05B43 (IC2) TMP95C061 (IC1) 2.2.2.3 EEPROM Control Circuits +5V 2.2.2.4 Timer Circuit 2.2.2.5 DRAM Control Rev. A 2-2 2.2.2.6 Print Head Control Circuit Page Common Waveform 64-dot 2-3 2.2.2.7 PF(Pump) Motor Drive Circuit Rev. A 2-31 2.2.2.8 CR Motor Drive Circuit Chapter 3 Disassembly and Assembly 3.1 OVERVIEW 3.1.1 Precautions for Disassembling the Printer WARNING 3- 3.1.2 Specification for Screws 3.1.3 Tools Chapter 3 Disassembly and Assembly Rev. A 3- 3.1.4 Work Completion Check 3- 3.2 DISASSEMBLY AND ASSEMBLY Figure 3-1. Disassembly Flow This section describes the step-by-step disassembly procedures shown in the diagram below. 3.2.1 Housing Removal WORK POINT 3.2.2 Circuit Boards Removal WORK POINT Page 3.2.3 Control Panel Removal 3.2.4 Waste Ink Pad Assembly Removal CAUTION WORK POINT 3.2.5 Disassembling the Printer Mechanism 3.2.5.1 Printhead Removal Page 3.2.5.2 Pump Assembly and Cap Assembly Removal CAUTION OK NG Page 3.2.5.3 CR Motor Assembly Removal WORK POINT Page 3.2.5.4 PF Motor Assembly Removal Page 3.2.5.5 ASF Assembly Removal Page 3.2.5.5.1 ASF Disassembly 3.2.5.5.2 Pick-Up Roller Assembly Removal 3.2.5.6 Carriage Assembly Removal Page 3.2.5.7 PF Roller Assembly Removal Page 3.2.5.8 PE Sensor Assembly Removal 3.2.5.9 HP Sensor Assembly Removal Chapter 4 Adjustment Rev. A 4-1 4.1 OVERVIEW 4.1.1 Required Adjustments CAUTION Performance Order 1 2 3 4 5 Note) : Required adjustment NA: Not applicable 4.2 Adjustments 4.2.1 Paper Gap Adjustment Figure 4-1. Paper Gap Adjustment - Thickness Gauge Setting Figure 4-2. Paper Gap Adjustment - Adjustment Procedure Figure 4-3. CLEANER, HEAD Overlap 4- 4.2.2 Adjustment using Adjustment Program 4.2.2.1 Overview of Adjustment Program 4.2.2.2 Ink Charge Operation CAUTION 4- 4.2.2.3 VH Setting Timing to write the specified value to EEPROM: Upon pressing ENTER key after ID code input. Head VH ID Viewed from front Page 4.2.2.4 Head Angular Adjustment Page Rev. A 4-11 4.2.2.5 Bi-D Alignment Adjustment Timing to write the specified value to EEPROM: Upon pressing ENTER key after input Y. 4-1 Chapter 5 Troubleshooting 5.1 Troubleshooting Page 5.2 Unit Level Troubleshooting 5.2.1 Printer does not operate at power on Is AC power voltage normal? Figure 5-2. Flow Chart 1 board opened? Is the fuse opend again? 5.2.2 Error is detected 5.2.3 Failure occurs during printing Figure 5-4. Flow Chart 3 5.2.4 Printer does not feed the paper correctly Figure 5-5. Flow Chart 4 5.2.5 Control panel operation is abnormal 5.3 Unit Repair C206 PSB/PSE Board Page 5-11 5.3.1 Unit Repair - C200 Main Board 5-1 5.4 Repair of the Printer Mechanism 5-1 Page Page Chapter 6 Maintenance Rev. A 6-1 6.1 OVERVIEW 6.1.1 Cleaning 6.1.2 Service Maintenance 6- 6.1.3 Lubrication Chapter 6 Maintenance Rev. A 6- No.12 *Never apply the oil exceeding 0.6cc. Page No.6 No.7 Page Appendix Rev.A A-1 A.1 Connector Summary A-2 A.2 Connector Summary Rev.A A-3 A-4 A.3 EEPROM Address Map Rev.A A-5 A-6 Rev.A A-7 Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page MMAAIINN BBRRDD OPERATOR PANEL PPRROOMM PH LOCK TAB PMPAS WASTE PAD EPSON OVERSEAS MARKETING LOCATIONS