FIG. 22
English
P
FIG. 23 |
| FIG. 24 |
Q |
FIG. 25
R
R
FIG. 26
S
T
FIG. 27 | U | FIG. 28 |
|
V
R
should contact the edge of the table extension and the main table (Fig. 7). When leveling, press the edge of the table extensions down to remove any play. For best results, use a level long enough to contact the edges of both table exten- sions.
If the table extensions are not level, loosen the jam nuts (T) and adjust the table extension support bolts (S) up or down (Fig. 26).
NOTE: The outside edges of the extension tables are level with the base while the inside edges (closest to the cutter head) are below the edge of the base. This is set at the fac- tory to reduce unnecessary friction between the material and the table while providing adequate support at the two points (those farthest from the cutter head) on the tables that are integral to snipe prevention.
TABLE
Keep the table clean and free from oil, grease and pitch. Treat the table with paste wax to help maintain its smooth finish.
Circuit Breaker Reset Button (Fig. 27)
Your planer is equipped with an 18 amp circuit breaker. If your planer becomes overloaded and stops operating, turn off the planer, let the unit sit for 2 minutes and press the reset button (U) before you resume working.
WARNING: To prevent the planer from starting unexpect- edly if power is interrupted by a circuit breaker trip, make sure the switch is in the OFF position before restoring power.
NOTE: Circuit breaker overload is often the result of dull knives. Change your knives on a regular basis to avoid trip- ping your breaker. Check your knives before
See the Troubleshooting Guide at the end of this section for more information.
Brushes
Inspect carbon brushes regularly. Keep brushes clean and sliding freely in their guides. Always replace a used brush in the same orientation in the holder as it was prior to its removal.
Carbon brushes have varying symbols stamped into their sides, and if the brushes are worn down to the line closest to
the spring, they must be replaced. Use only identical DEWALT brushes.
New brush assemblies are available at DEWALT service centers. After replacing brush assemblies, the tool should be allowed to “run in” (run at no load) for 10 minutes to seat new brushes before using.
TO REMOVE BRUSH ASSEMBLY (FIG. 28)
WARNING: DISCONNECT TOOL FROM THE POWER SOURCE BEFORE ATTEMPTING TO REMOVE BRUSH ASSEMBLY.
1.Remove the brush inspection cap (V).
2.Withdraw the brush assembly.
Cleaning and Lubrication
CAUTION: Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Electric shock may result.
CAUTION: Never use solvents or other harsh chemicals for cleaning the
It is recommended that, once a year, you take or send the tool to a DEWALT certified service center for a thorough cleaning, inspection and lubrication of the gear case.
Accessories
There are three accessories available for the DW734 thick- ness planer:
•DW7331 – Dust Hood for DW734 (also fits the DW733)
•DW7342 –
•DW7350 – Mobile Stand
CAUTION: The use of any other accessory not recom- mended for use with this tool could be hazardous.
If you need any assistance in locating these accessories, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 or call
Repairs
To assure product SAFETY and RELIABILITY, repairs, main- tenance and adjustment should be performed by authorized service centers or other qualified service personnel. Always use identical replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty cov- erage and warranty repair information, visit www.dewalt.com or call
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase.
6
