Picture adjustment
Adjustment from personal computer
Although this projector sets proper signal systems automatically for the image signal from personal computers, it cannot be applied to some of personal computers. In this case, press AUTO POSITION button. If the images are still not projected correctly, use MENU display to adjust the projected images from personal computers. Also available to memorize the setting.
ENGLISH | Adjusting the images form personal |
| |
| computers in MENU display |
| Adjust as below for the following symptoms. |
| AUTO | HORIZ. | VERT. | FINE SYNC. | TRACKING | RGB/Y,CB,CR |
|
| |
| POSITION | POSITION |
|
| |||||
| AUTO |
|
|
|
| RGB | USER |
| |
| SXGA70a | 0 | 0 | 0 | 0 | Y,CB,CR | MEMORIZE |
| |
| USER1 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| DELETE |
| |
| USER2 |
|
|
|
|
| RESET |
| |
|
|
|
|
|
|
|
| ||
SIGNAL | PICTURE | PinP/ | PC CARD | AUDIO | INSTALLATION | OPTION | Ver. | ||
EXPAND | AUTO PLAY | ||||||||
|
|
|
|
|
| ||||
Image moves to right or left :
Adjust HORIZ. POSITION in SIGNAL menu. Press the º button on the control panel (or } button on the remote control) to move the image to left. Press the ª button on the control panel (or { button on the remote control) to move the image to right.
Image moves to up or down :
Adjust VERT. POSITION in SIGNAL menu. Press the º button on the control panel (or } button on the remote control) to move the image to upward.
Press the ª button on the control panel (or { button on the remote control) to move the image to down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
SIGNAL - USER
| CLAMP | CLAMP | HORIZ. |
|
| VERT. | PLL | VERT. |
| HOLD |
| ||||||
| POSITION | WIDTH | PIXELS |
|
| LINES | SYNC. |
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
| AUTO | AUTO | AUTO |
| ||
| 33 | 33 | 3333 |
|
|
| 3333 | FAST | ON | ON |
| BEGIN | END | ||||
|
|
|
|
|
|
|
|
|
|
|
| NORMAL | OFF | OFF |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| SLOW |
| 33 | 33 | ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of each menu in SIGNAL - USER menu.
Noise etc. appears on right or left side of image: Adjust HORIZ. PIXELS of the menu in SIGNAL - USER menu.
Noise etc. appears on top or bottom part of image : Adjust VERT. LINES of the menu in SIGNAL - USER menu.
Top part of image curves :
Change the setting of PLL or HOLD of the menu in SIGNAL - USER menu.
PLL ....... Select FAST, NORMAL, or SLOW for
image which top part is the least curved. Select AUTO for normal setting.
HOLD ... Select ON, and adjust BEGIN or END for image which top part is the least curved.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL - USER menu. Select AUTO for normal setting.
•Do not change each menu setting in SIGNAL - USER menu for normal setting.
Memorizing the setting
1.Select MEMORIZE in SIGNAL menu, and press ENTER button.
2.Press the 
button on the control panel (or % button on the remote control).
3.Press theª or ºbuttons on the control panel (or { or } buttons on the remote control) to select the memory which you wish to record (USER 1 or USER 2)
4.Press ENTER button.
Initializing the setting which has been changed
Select DELETE in SIGNAL menu, and press ENTER button.
•While INITIALIZING, buttons do not work about 2 - 18 seconds. Use them to operate after initial- izing is finished.
Seeing images in recorded setting.
Select AUTO in SIGNAL menu, and press theª or ºbuttons on the control panel (or { or } buttons on the remote control) to select the memory (USER1 or USER2).
Resetting the recorded setting
1.Select RESET in SIGNAL menu, and press EN- TER button.
2.Press the 
button on the control panel (or % button on the remote control).
3.Press theª or º buttons on the control panel (or { or } buttons on the remote control) to select the memory which you wish to reset (USER 1 or USER 2).
4.Press ENTER button
The recorded setting will be reset.
The simple way of adjustment
1.Horizontal position:
Adjust the start position (the left end) using HORIZ. POSITION, and adjust the end position (the right end) using TRACKING. Then repeat these steps.
2.Vertical position:
Adjust the start position using VERT. POSITION.
22
