Installation and Operation, cont’d
DVI 201 Tx Rear Panel |
|
| |||
POWER | DDC ROUTE |
|
| DVI 201 Tx | |
12V |
| REMOTE |
|
| |
0.4A MAX |
|
|
| ||
|
|
| PASS THRU | ||
|
|
|
|
| |
| SPARE | LOCAL | 1 | 2 | Tx Rx |
5 |
|
|
| 6 | 4 |
DVI 201 A D Tx Rear Panel
| O | 1 | DVI 201 |
|
| A D Tx |
| ||
| U |
| ||
|
|
| ||
| T |
|
| 6 |
| P |
|
| |
| U |
|
|
|
| T | 2 |
|
|
| S |
|
|
|
7 |
|
| R |
|
CONNECT | AUDIO OUTPUT |
| ||
| DO NOT |
|
| |
| TO LAN | L |
| |
|
|
| POWER 12V 0.4AMAX | 5 |
|
|
|
|
Figure 2-13 — DVI 201 Tx rear panel connectors
A | DVI input connector — Connect a DVI cable between this port |
| and the DVI output port of the digital video source. See "DVI |
| connector pin assignments," on page |
B | Local output (DVI 201 Tx |
| connect a DVI monitor for local monitoring of the input digital |
| image. See "DVI connector pin assignments," on page |
| pin assignments. |
NIn a system where the local output is not used, ensure that you power up the end display first before the video source. Route the DDC to the remote end (see the
DDC Route DIP switch [item B, in "Operation", on page
C | Audio input (DVI 201 A D Tx [Decora] only) — Connect an | |||||||||||||||||||
| unbalanced stereo audio source to this 3.5 mm mini stereo jack | |||||||||||||||||||
| for unbalanced audio input. Figure | |||||||||||||||||||
| audio plug. | |||||||||||||||||||
| Tip (L+) |
|
| Sleeve (Gnd) | ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Ring (R+) | ||||||||||||||||
|
|
|
|
|
|
|
| Tip (L+) | ||||||||||||
|
|
|
|
|
|
|
|
|
|
| Sleeve (Gnd) | |||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||
| Figure | |||||||||||||||||||
D | ||||||||||||||||||||
| this 3.5 mm, |
| N The |
| modulated infrared (IR) signals. See "Modulated IR |
| pass through" on page |
E | DC power input connector — Plug the included external |
| 12 VDC power supply into either this connector or the power |
| input connector on the receiver (item K on page |
| "Power supply wiring," on page |
F | Transmitter output connector — Connect one end of two |
| separate TP cables to these |
| transmitter. |
| C Do not connect these devices to a computer data or |
| telecommunications network. |
| N In order to fit in the junction box, the TP cables and |
| |
| Connect the free ends of the same TP cables from the transmitter |
| to the receiver’s Input |
| page |
| DVI 201 Tx/Rx • Installation and Operation |