Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic CrossPoint 128 Control/remote - switcher, General, Audio - audio models only

Models: CrossPoint 124 CrossPoint 128 CrossPoint 84 CrossPoint 168 84, 88, 124, 128, 168, 1616 HV, 1616HVA CrossPoint 88

1 70

Download 70 pages 47.83 Kb

Page 57

Audio — audio models only

Routing	84 Series	8 x 4 stereo matrix
	88 Series	8 x 8 stereo matrix
	124 Series	12 x 4 stereo matrix
	128 Series	12 x 8 stereo matrix
	168 Series	16 x 8 stereo matrix
	1616 Series	16 x 16 stereo matrix
Gain	Unbalanced output: 0dB, balanced output: +6dB
Frequency response	20 Hz to 20 kHz, ±0.05dB
THD + Noise	0.03% @ 1 kHz at at nominal level
S/N	>90dB, balanced, at rated maximum output (21dBu)
Crosstalk	<-80dB @ 1 kHz, fully loaded
Stereo channel separation	>80dB @ 1 kHz
CMRR	>75dB @ 20 Hz to 20 kHz

Audio input — audio models only

Number/signal type	8, 12, or 16 stereo, balanced/unbalanced
Connectors	(8, 12, or 16) 3.5 mm captive screw connectors, 5 pole
Impedance	>10 kohms unbalanced/balanced, DC coupled
Nominal level	-10dBV (316mV)
Maximum level	+19.5dBu, (balanced or unbalanced) at 1%THD+N
Input gain adjustment	-15dB to +9dB, adjustable per input by RS-232 or front panel

Audio output — audio models only

Number/signal type	4, 8, or 16 stereo, balanced/unbalanced
Connectors	(4, 8, or 16) 3.5 mm captive screw connectors, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±0.1dB channel to channel
Maximum level (Hi-Z)	>+21dBu, balanced or unbalanced at stated %THD+N
Maximum level (600 ohm)	>+15dBm, balanced or unbalanced at stated %THD+N

0dBu = 0.775 volts (RMS).

Control/remote — switcher

Serial control port	1	RS-232 or RS-422, 9-pin female D connector
Baud rate and protocol	9600, 8-bit, 1 stop bit, no parity
Serial control pin configurations ....	2	= TX, 3 = RX, 5 = GND
Program control	Extron’s control program for Windows®
	Extron’s Simple Instruction Set™ – SIS™

General

Power	100VAC to 240VAC, 50/60 Hz, internal, autoswitchable
	84/88/124/128 Series	30 watts
	168/1616 Series	36 watts
Temperature/humidity	Storage -40° to +158°F (-40° to +70°C) / 10% to 90%, non-condensing
	Operating +32° to +104°F (0° to +40°C) / 10% to 90%, non-condensing
Rack mount	Yes, with included parts
Enclosure type	Metal
Enclosure dimensions
84/88/124/128 Series	5.25" H x 17.0" W x 9.4" D (3U high, full rack width)
	(13.3 cm H x 43.2 cm W x 23.9 cm D)
	(Depth excludes connectors. Width excludes rack ears.)

CrossPoint Matrix Switchers • Specifications

A-3

Image 57

Extron electronic CrossPoint 128, CrossPoint 88 manual Control/remote - switcher, General, Audio - audio models only

Contents

CrossPoint 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Matrix Switchers68-353-02 Rev. E Printed in the USA Safety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen DeutschInstallation Quick Start - CrossPoint Matrix SwitchersConfiguration - One or more ties or sets of ties DefinitionsSave or recall a preset Quick Start - CrossPoint Matrix Switchers, cont’dView and adjust audio level Front Panel ControlsCrossPoint Matrix Switchers Table of Contents Table of Contentsii CrossPoint Matrix Switchers Table of Contents Table of Contents, cont’dAbout the CrossPoint Series Matrix Switchers Features CrossPoint Matrix SwitchersChapter1One IntroductionAbout the CrossPoint Series Matrix Switchers 1-2 CrossPoint Matrix Switchers IntroductionIntroductiontroduction, cont’d Features Figure 1-1 - A typical CrossPoint Matrix Switcher applicationCrossPoint Matrix Switchers Introduction Introduction, cont’d 1-4 CrossPoint Matrix Switchers IntroductionFigure 1-2 - Audio gain and attenuation Any input to any or all outputsCrossPoint Matrix Switchers Introduction Introduction, cont’d 1-6 CrossPoint Matrix Switchers IntroductionRack Mounting the Switcher Cabling and Rear Panel Views InstallationChapter2Two CrossPoint Matrix SwitchersRack Mounting the Switcher Installationstallation, cont’dPower connection Figure 2-1 - Rear panel connectors, CrossPoint 128HVACrossPoint Matrix Switchers Installation Figure 2-3 - Captive screw connector wiring for inputsVideo input and output connections Audio input and output connections HVA models onlyFigure 2-4 - Typical audio connectors Installation, cont’dFigure 2-5 - Captive screw connector wiring for audio output 9-pin D connector for serial RS-232/422 controlFigure 2-7 - Rear panel view, CrossPoint 84HVA Figure 2-6 - Rear panel view, CrossPoint 84HVFigure 2-8 - Rear panel view, CrossPoint 88HV Figure 2-9 - Rear panel view, CrossPoint 88HVAFigure 2-11 - Rear panel view, CrossPoint 124HVA 2-6 CrossPoint Matrix Switchers InstallationFigure 2-12 - Rear panel view, CrossPoint 128HV Figure 2-13 - Rear panel view, CrossPoint 168HVFigure 2-15 - Rear panel view, CrossPoint 1616HV Figure 2-14 - Rear panel view, CrossPoint 168HVACrossPoint Matrix Switchers Installation 1 3 5Installation, cont’d 2-8 CrossPoint Matrix Switchers InstallationRear Panel Controls Troubleshooting Worksheets Front Panel Controls and Indicators Front Panel OperationsChapter3Three Operation3-2 CrossPoint Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d DefinitionsCrossPoint Matrix Switchers Operation Input buttons, output buttons, and LEDsControl buttons and LEDs Operation, cont’d 3-4 CrossPoint Matrix Switchers OperationI/O controls Front panel I/O label windowsCreating a configuration PowerFront Panel Operations CrossPoint Matrix Switchers OperationExample 1 Create a set of video and audio ties 3-6 CrossPoint Matrix Switchers OperationFigure 3-4 - Example 1 Creating a tie Example 2 Add a tie to a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Figure 3-5 - Example 2 Adding a video tieFigure 3-6 - Example 3 Selecting audio, selecting input CrossPoint Matrix Switchers Operation3-8 CrossPoint Matrix Switchers Operation Viewing a configurationFigure 3-7 - Example 3, step D Removing an audio tie Example 4 View video and audio, audio-only, and video-only tiesCrossPoint Matrix Switchers Operation 3-10 CrossPoint Matrix Switchers Operation Muting and unmuting video and/or audioOperation, cont’d Example 5 Muting and unmuting an output CrossPoint Matrix Switchers Operation1. You can mute video and audio, video-only, or audio-only outputs. Pressing and releasing the RGBHV and Audio buttons toggles each selection on and off Example 6 Save a preset Using presetsFigure 3-13 - Example 6 Saving the current configuration as preset 3-12 CrossPoint Matrix Switchers OperationExample 7 Recall a preset Viewing and adjusting the audio level HVA models onlyFigure 3-14 - Example 7 Recalling preset Example 8 View and adjust an audio level3-14 CrossPoint Matrix Switchers Operation Operation, cont’d= off value 0 dB Figure 3-16 - +8dB displayed, CrossPoint 168 and Figure 3-18 - -1dB displayed, CrossPoint 168 and CrossPointCrossPoint Matrix Switchers Operation Front panel security lockout executive mode TroubleshootingSystem reset to factory defaults 3-16 CrossPoint Matrix Switchers OperationWorksheets Plasma display S-video problemGeneral checks Worksheet example 1 Entering system equipment3-18 CrossPoint Matrix Switchers Operation Figure 3-20 - Worksheet example 2 Status meeting configurationWorksheet example 2 Drawing ties Operation, cont’dWorksheet example 3 Test configuration Figure 3-21 - Worksheet example 3 Test configurationCrossPoint Matrix Switchers Operation Operation, cont’d 3-20 CrossPoint Matrix Switchers OperationCrossPoint Matrix Switchers Operation Matrix Switchers Configuration WorksheetPreset # Indicate if the configuration is for Video, Audio, or bothOperation, cont’d 3-22 CrossPoint Matrix Switchers OperationSwitcher Error Responses Using the Command/Response Table Host-to-Switcher Instructions Switcher-Initiated MessagesCommand/Response Table Chapter4FourSwitcher-Initiated Messages Host-to-Switcher InstructionsFigure 4-1 - RS-232/RS-422 connector pin arrangement 4-2 CrossPoint Matrix Switchers Programmer’s GuideSwitcher Error Responses Using the Command/Response TableCrossPoint Matrix Switchers Programmer’s Guide Command/response table for SIS commands Command/Response TableSymbol Definitions CommandCommand Command/response table for SIS commands Cont’dASCII Command CrossPoint Matrix Switchers Programmer’s GuideCommand/response table for SIS commands Cont’d 4-6 CrossPoint Matrix Switchers Programmer’s GuideCommand ASCII CommandChapter5Five Matrix Switcher+ Control Program Button-Label GeneratorMatrix Software CrossPoint Matrix SwitchersInstalling the software Matrix Switcher+ Control ProgramUsing the software Overview 5-2 CrossPoint Matrix Switchers Matrix SoftwareCrossPoint Matrix Switchers Matrix Software Figure 5-1 - Extron Matrix Switcher+ Control Program window blankFigure 5-2 - Sample program window complete Windows buttonsMatrix Software, cont’d 5-4 CrossPoint Matrix Switchers Matrix SoftwareWindows menus File menuUsing the help system Using emulation modeUsing the software Button-Label Generator5-6 CrossPoint Matrix Switchers Matrix Software Figure 5-3 - Extron’s Button-Label Generator windowMatrix Software, cont’d Specifications Part Numbers SpecificationsAAppendix A CrossPoint Matrix SwitchersA-2 CrossPoint Matrix Switchers Specifications Specificationsecifications, cont’dVideo Video inputCrossPoint Matrix Switchers Specifications Control/remote - switcherGeneral Audio - audio models onlyA-4 CrossPoint Matrix Switchers Specifications Specifications, cont’dPart Numbers Extron PartAssorted connectors RG6 super high resolution cableBNC connectors CablesSpecifications, cont’d A-6 CrossPoint Matrix Switchers SpecificationsExtron Part BNC-5 Mini HR CableAppendixBB Hardware Upgrades Button LabelsReference Information CrossPoint Matrix SwitchersOpening the switcher Hardware UpgradesReferenceInformation,co t’d Opening the CrossPoint 84, 88, 124, andCrossPoint Matrix Switchers Reference Information Opening the CrossPoint 168 andFigure B-2 - Removing the front cover B-4 CrossPoint Matrix Switchers Reference Information Closing the switcherReference Information, cont’d Swapping the serial portsReconnect the input and output cables Installing a firmware updateFigure B-4 - Key and pin 1 mark CrossPoint Matrix Switchers Reference InformationButton Labels B-6 CrossPoint Matrix Switchers Reference InformationReplacing the AC fuse CrossPoint 84, 88, 124, and 128 only Reference Information, cont’dCrossPoint Matrix Switchers Reference Information Figure B-5 - Button label blanks, 16-button stripReference Information, cont’d B-8 CrossPoint Matrix Switchers Reference InformationFCC Class A Notice Extron’s WarrantyUSA, Canada, South America Europe, Africa, and the Middle EastExtron Electronics, Europe Extron Electronics, USAExtron Electronics, Asia Extron Electronics, Japan