Extron electronic HDMI 201 Rx Pin assignments and wiring, Hdmi connector pin assignments

Installation and Operation, cont’d

L	Output Audio — Plug an audio device into this pair, left and
	right, of female RCA connectors (figure 2-14) for an unbalanced
	stereo audio signal.

Pin assignments and wiring

HDMI connector pin assignments

Figure 2-19 defines the pinout for the HDMI protocol.

	1	19
19	1

	18	HDMI	2			2 HDMI 18
	Type A Receptacle					Type A Plug
Pin	Signal			Pin	Signal		Pin	Signal
1	TMDS data 2+			7	TMDS data 0–		13	CEC control*
2	TMDS data 2			8	TMDS data 0		14	Reserved
	shield				shield			(NC)
3	TMDS data 2-			9	TMDS data 0-		15	SCL
4	TMDS data 1+			10	TMDS clock+		16	SDA
5	TMDS data 1			11	TMDS clock		17	DDC / CEC
	shield				shield			Ground
6	TMDS data 1-			12	TMDS clock-		18	+5 V power
* CEC control on pin 13 is a proprietary							19	Hot plug detect
usage, not the industry standard.

Figure 2-19 — HDMI connectors

TP cable termination

NRJ-45 termination with CAT 5, CAT 5e, or

CAT 6 cable must comply with the TIA/EIA T 568A or

TIA/EIA T 568B wiring standard for all connections.

Figure 2-20 details the recommended termination of TP cables with RJ-45 connectors in accordance with either the TIA/EIA T 568A or the TIA/EIA T 586B wiring standard.

Side		Pins:		RJ-45
	1 2 3 4 5 6 78
				Connector
				TIA/EIA T	TIA/EIA T	Signal
				586 A	586 B
			Pin	Wire color	Wire color	RJ-45 #1	RJ-45 #2
			1	White-green	White-orange	Data 0+	CEC
			2	Green	Orange	Data 0–	HPD
			3	White-orange	White-green	ID Clock+	RS-232
							TX
			4	Blue	Blue	Data 1+	DDC Clk
			5	White-blue	White-blue	Data 1–	+12 V
		Insert
			6	Orange	Green	ID Clock–	RS-232
		Twisted					RX
	Pair Wires		7	White-brown	White-brown	Data 2+	DDC data
			8	Brown	Brown	Data 2–	Ground

NTerminate both ends of both cables identically, in accordance with either the TIA/EIA T 568A or the TIA/EIA T 568B wiring standard.

Figure 2-20 — TP cable termination

NDo not use Extron’s UTP23SF-4 Enhanced Skew-Free™A/V UTP cable to link the transmitter and receiver. Skew-free A/V cable was designed for most Extron

TP transmitter/receiver applications, but the

HDMI 201 Tx/Rx does not work properly with this cable.

NIn order to fit in the junction box, the TP cables and RJ-45 connectors should not have a boot installed.

NIf necessary, test for proper cable connection (output 1 to input 1, output 2 to input 2) as follows:

1. Plug both TP cables into the powered unit.

2. Momentarily connect either of the cables on the opposite end into the unpowered unit‘s “2” connector.

If the unpowered unit’s Power LED is lit, the connection is correct.

If the unpowered unit’s Power LED is not lit, unplug the connector on the unpowered end and connect the other cable to the “2” connector.

2-22 HDMI 201 Tx/Rx • Installation and Operation HDMI 201 Tx/Rx • Installation and Operation 2-23