Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic HSA 200S Maintenance and Modifications, cont’d, 3 - Removing the front panel

Models: HSA 200SE HSA 200S HSA 222C

1 30

Download 30 pages 34.8 Kb

Page 19

Figure 3-3 — Removing the front panel

Maintenance and Modifications, cont’d

4. Remove the four 1/16" hex head screws on the right and left sides of the front panel (figure 3-3). Retain the screws. Lift the panel away from the enclosure.

Figure 3-3 shows an HSA 200 model. Removing the front panel from an HSA 222 is an identical procedure.

Remove 2 hex head screws on each side.

240-

Hz 5A

HSA	200

AUDIO

Lift panel out of enclosure.

Figure 3-3 — Removing the front panel

5.	With a Tweeker, push down on and
	gently twist on the front of each RJ-45
	connector detent to disconnect the
	connector from the rear of the front panel
	plug-in.
6.	Pinch the top and bottom bezel detents
	together and push the bezel through the
	front panel.
7.	Snap a replacement bezel in place. If necessary, replace the
	connector icon by prying the old icon off of the connector
	plug-in with a Tweeker (figure 3-4) and snapping a new
	icon in place.

Icon Label

Figure 3-4 — Changing the connector icon

8.	Snap the internal RJ-45 connector onto the back of the front
	panel enclosure bezel plug-in.
9.	(HSA 222 models only) Reach your hand through the
	front panel access hole and snap the lower internal RJ-45
	connectors onto the back of the lower enclosure bezel
	plug-ins.

10. Replace the front panel in the surface mount enclosure and secure it in place with the hex head screws removed in step 4.

11. (HSA 222 models only) Replace the front access panel in the surface mount enclosure and secure it in place with the Philips head screws removed in step 2.

12. (HSA 222 models only) Reinstall the surface mount enclosure. See Removing and Replacing the Enclosure, steps 6 through 11.

3-6 HSA 200/222 Series • Maintenance and Modifications

HSA 200/222 Series • Maintenance and Modifications 3-7

Image 19

Extron electronic HSA 200S Maintenance and Modifications, cont’d, HSA 200/222 Series Maintenance and Modifications

Contents

2008 Extron Electronics. All rights reserved HSA 200S & HSA 200SE HSA 200C & HSA 200CE HSA 222S & HSA 222CUser’s Manual 68-695-01 Rev. HSafety Instructions English PrecautionsExtron’s Warranty FCC Class A NoticePage Pre-installation Testing and Troubleshooting Table of ContentsAbout the Hideaway Surface Access Products Underside Features and Cabling ConnectionsIntroduction HSA 200/222 Series Surface Access ProductsTable of Contents, cont’d Chapter1OneFigure 1-1 - HSA 200C hideaway enclosure About the Hideaway Surface Access ProductsIntroduction The HSA 200C figure 1-1 and HSA 200S figure 1-2 provideAll models FeaturesIntroduction About the Extender board line driverInstallation Overview Preparing the Routing Template InstallationIntroduction HSA 200/222 Series Surface Access Products Chapter2Two8 On HSA 200SE and HSA 200CE models, set the gain switch InstallationInstallation Overview Preparing the Routing TemplatePreparing the table with a router Installation, cont’d Preparing the Table and Mounting the EnclosureFigure 2-2 - Cutting the opening with a router example Figure 2-3 - Cutting the opening with a hole saw Installation, cont’dHideaway Surface Access Enclosure Extron HSAFigure 2-6 - HSA 200S and HSA 200C audio connector Underside Features and Cabling ConnectionsInstallation, cont’d Figure 2-5 - HSA 200CE under-table featuresHSA 200CE and HSA 200SE Extender board only Installation, cont’dFigure 2-8 - Configuration of RJ-45 connectors All HSA 200 and HSA 222 modelsFigure 2-10 - Powering the Extender board Front Panel ConnectorsInstallation, cont’d Power connector wiringFigure 2-15 - Configuration of RJ-45 connectors Installation, cont’d3 Audio input connector HSA 200 models only - Plug a Figure 2-14 - Audio input connector plugInstallation, cont’d Maintenance and ModificationsChapter3Three HSA 200/222 Series Surface Access ProductsHSA 200 models only The audio connector Maintenance and ModificationsRemoving and Replacing the Enclosure Replacing the Bezelswhile you Maintenance and Modifications, cont’dFigure 3-1 - Removing the front access panel HSA 222 models HSA 200/222 Series Maintenance and ModificationsHSA 200/222 Series Maintenance and Modifications Maintenance and Modifications, cont’d3-6 HSA 200/222 Series Maintenance and Modifications Figure 3-4 - Changing the connector iconFigure 3-5 - Removing the gas lift mounting plate Maintenance and Modifications, cont’d Replacing the Gas Lift3-8 HSA 200/222 Series Maintenance and Modifications HSA 200/222 Series Maintenance and ModificationsHSA 200/222 Series Maintenance and Modifications Maintenance and Modifications, cont’d3-10 HSA 200/222 Series Maintenance and Modifications Figure 3-7 - Front access panel removal HSA 222 modelsHSA 200/222 Series Maintenance and Modifications Adjusting the Top PanelMaintenance and Modifications, cont’d Figure 3-10 - Adjusting the top panelMaintenance and Modifications, cont’d AAppendix AReference Information HSA 200/222 Series Surface Access ProductsReference Information SpecificationsHSA 200C, HSA 200CE - USA models Reference Information, cont’dHSA 200S, HSA 200SE - USA models HSA 222S - USA modelAll nominal levels are at ±10% HSA Part NumbersSpecifications are subject to change without notice Reference Information, cont’dReference Information, cont’d Included Parts Replacement PartsAccessories Top Plate DimensionsUser Access Connectors and AAP Openings TEMPLATE IS NOT FULL SIZE Appendix BPackaging for Shipment HSA 200/222 Series Surface Access ProductsFigure B-1 - HSA 200/HSA 222 return kit Packaging for ShipmentFigure B-2 - Installing protective strips Figure B-3 - Installing the HSA into the foam shellFigure B-5 - HSA in the shipping carton Packaging for Shipment, cont’dB-4 HSA 200/222 Series Packaging for Shipment Figure B-4 - HSA unit suspended in the foam