Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic HSA 200SE Maintenance and Modifications, cont’d Replacing the Gas Lift

Models: HSA 200SE HSA 200S HSA 222C

1 30

Download 30 pages 34.8 Kb

Page 20

Maintenance and Modifications, cont’d

Maintenance and Modifications, cont’d

Replacing the Gas Lift

The gas lift that raises the HSA surface is rated for 100,000 opening and closing cycles. Replace the gas lift as follows:

				Ensure that AC power is disconnected before
				servicing the HSA unit.
				When the HSA 200 is upside-down, the latch may
CAUTION				When the HSA 200 is upside-down, the latch may
				be ineffective. If the latch releases in this position,
				the enclosure will tip and could damage the flanged
				edges. Keep a free hand on the enclosure to keep it
				from tipping.

1.	Remove the surface mount enclosure from the table. See
	Removing and Replacing the Enclosure, steps 1 through 4.
	Place the enclosure upside-down on a horizontal surface.
	To protect the finish, place the enclosure on a soft cloth.
2.	Loosen the three Philips head screws that secure the gas
	lift mounting plate in place (figure 3-5).

Unscrew mounting plate from gas lift.

Loosen (3) screws.

Figure 3-5 — Removing the gas lift mounting plate

		Figure 3-5 shows an HSA 200 model. Removing the gas
		lift mounting plate from an HSA 222 is an identical
		procedure.
3.	Slide the gas lift mounting plate toward the center of the
	enclosure, releasing the mounting plate (figure 3-5).
4.	Turn the gas lift mounting plate counterclockwise until the
	plate comes free from the shaft of the gas lift (figure 3-5).

5. Turn the surface mount enclosure onto its back side and open the top panel.

With the gas lift removed, the top panel must be manually lifted.

6.(HSA 200 models only) Remove the four 1/16" hex head screws on the right and left sides of the front panel (figure 3-6). Retain the screws. Lift the panel away from the enclosure.

Figure 3-6 shows an HSA 200 model. Removing the front panel from an HSA 222 is an identical procedure.

Remove 2 hex head screws on each side.

-

HSA	200

AUDIO

Lift panel out of enclosure.

Figure 3-6 — Front panel removal (HSA 200 models)

3-8 HSA 200/222 Series • Maintenance and Modifications

HSA 200/222 Series • Maintenance and Modifications 3-9

Image 20

Extron electronic HSA 200SE, HSA 222C user manual Maintenance and Modifications, cont’d Replacing the Gas Lift

Contents

HSA 200S & HSA 200SE HSA 200C & HSA 200CE HSA 222S & HSA 222C User’s Manual68-695-01 Rev. H 2008 Extron Electronics. All rights reservedPrecautions Extron’s WarrantyFCC Class A Notice Safety Instructions EnglishPage Table of Contents About the Hideaway Surface Access ProductsUnderside Features and Cabling Connections Pre-installation Testing and TroubleshootingHSA 200/222 Series Surface Access Products Table of Contents, cont’dChapter1One IntroductionAbout the Hideaway Surface Access Products IntroductionThe HSA 200C figure 1-1 and HSA 200S figure 1-2 provide Figure 1-1 - HSA 200C hideaway enclosureFeatures IntroductionAbout the Extender board line driver All modelsInstallation Introduction HSA 200/222 Series Surface Access ProductsChapter2Two Installation Overview Preparing the Routing TemplateInstallation Installation OverviewPreparing the Routing Template 8 On HSA 200SE and HSA 200CE models, set the gain switchFigure 2-2 - Cutting the opening with a router example Installation, cont’d Preparing the Table and Mounting the EnclosurePreparing the table with a router Installation, cont’d Hideaway Surface Access EnclosureExtron HSA Figure 2-3 - Cutting the opening with a hole sawUnderside Features and Cabling Connections Installation, cont’dFigure 2-5 - HSA 200CE under-table features Figure 2-6 - HSA 200S and HSA 200C audio connectorInstallation, cont’d Figure 2-8 - Configuration of RJ-45 connectorsAll HSA 200 and HSA 222 models HSA 200CE and HSA 200SE Extender board onlyFront Panel Connectors Installation, cont’dPower connector wiring Figure 2-10 - Powering the Extender boardInstallation, cont’d 3 Audio input connector HSA 200 models only - Plug aFigure 2-14 - Audio input connector plug Figure 2-15 - Configuration of RJ-45 connectorsMaintenance and Modifications Chapter3ThreeHSA 200/222 Series Surface Access Products Installation, cont’dMaintenance and Modifications Removing and Replacing the EnclosureReplacing the Bezels HSA 200 models only The audio connectorMaintenance and Modifications, cont’d Figure 3-1 - Removing the front access panel HSA 222 modelsHSA 200/222 Series Maintenance and Modifications while youMaintenance and Modifications, cont’d 3-6 HSA 200/222 Series Maintenance and ModificationsFigure 3-4 - Changing the connector icon HSA 200/222 Series Maintenance and ModificationsMaintenance and Modifications, cont’d Replacing the Gas Lift 3-8 HSA 200/222 Series Maintenance and ModificationsHSA 200/222 Series Maintenance and Modifications Figure 3-5 - Removing the gas lift mounting plateMaintenance and Modifications, cont’d 3-10 HSA 200/222 Series Maintenance and ModificationsFigure 3-7 - Front access panel removal HSA 222 models HSA 200/222 Series Maintenance and ModificationsAdjusting the Top Panel Maintenance and Modifications, cont’dFigure 3-10 - Adjusting the top panel HSA 200/222 Series Maintenance and ModificationsAAppendix A Reference InformationHSA 200/222 Series Surface Access Products Maintenance and Modifications, cont’dSpecifications Reference InformationReference Information, cont’d HSA 200S, HSA 200SE - USA modelsHSA 222S - USA model HSA 200C, HSA 200CE - USA modelsHSA Part Numbers Specifications are subject to change without noticeReference Information, cont’d All nominal levels are at ±10%Replacement Parts AccessoriesTop Plate Dimensions Reference Information, cont’d Included PartsAppendix B Packaging for ShipmentHSA 200/222 Series Surface Access Products User Access Connectors and AAP Openings TEMPLATE IS NOT FULL SIZEPackaging for Shipment Figure B-2 - Installing protective stripsFigure B-3 - Installing the HSA into the foam shell Figure B-1 - HSA 200/HSA 222 return kitPackaging for Shipment, cont’d B-4 HSA 200/222 Series Packaging for ShipmentFigure B-4 - HSA unit suspended in the foam Figure B-5 - HSA in the shipping carton