OLLA:Layout 1 24/01/2008 16:16 Page 16
ENGLISH | 2. Select the desired cooking program and cooking time by pressing the cor- |
| responding program button (high/low pressure, rice cooking or slow cooker) |
| following the instructions for each program. |
| 3. Press the START/STOP button. The |
| delay set time has elapsed. |
| |
| CAUTION: DO NOT LEAVE PERISHABLE FOODS SUCH AS MEAT,POULTRY, FISH, |
| CHEESE AND DAIRY PRODUCTS AT ROOM TEMPERATURE FOR MORE THAN 2 |
| HOURS (OR MORE THAN 1 HOUR WHEN THE ROOM TEMPERATURE IS ABOVE |
| 90°F). WHEN COOKING WITH THESE FOODS, DO NOT SET T HE DELAY TIME |
| FUNCTION FOR MORE THAN |
| FOR EXAMPLE: say it is 10am and you want your dinner to be ready by 6pm. |
| Your recipe calls for 12 minutes of high pressure cooking. You can program |
| your delay time for 7 and a half hours and then the pressure cooking program |
| for 12 minutes. You do this by pressing the delay time button until the panel |
| reads 7.5 and then the high pressure setting button until it reads 12. Next you |
| press the start/stop button, and you’re all set. The cooker will start cooking at |
| 5:30 pm and your dinner will be ready at 5:42pm. The automatic warm func- |
| tion will ensure that it doesn’t get cold! |
| Cleaning and Maintenance |
Do not wash any parts of the
1.Unplug and let the unit cool before cleaning.
2.Remove the removable cooking pot and wash with warm soapy water or in the dishwasher. Rinse and dry thoroughly.
3.Wipe the outer housing with a clean damp cloth. Do not submerge in water.
4.Remove the condensation res ervoir by pul ling it down. Wash with warm, soapy water. Rinse and dry thoroughly. Replace by pushing into place.
5.Turn the lid upside down; grip the silicon e gasket and pull up to remove. Clean the silicone gasket with warm soapy water. Rinse and dry thoroughly. Replace the gasket by positioning it inside the edge of the lid and pushing
it down. Make sure the groove in the center of the gasket i s positioned around the m etal ring on the inside edge of the lid . NOTE: The s ilicone gasket must always be properly positione d on the underside of the lid; otherwise the unit will not work. Check periodically to make sure that it is clean, flexible, and not cracked or torn. (See pg. 10 “Getting started”)
6.If the silicone gasket appears damaged, cracked or torn, do not use the unit and contact our customer service department at
7.For optimal performance, the bottom of the
8.Never use abrasive cleaners or scouring pads to clean any of the parts. NOTE: Store the
Cleaning the Pressure Regular Knob
ALWAYS check that the pressure regulator knob and the pressure safety valves are in good working order before each use.
1. | After the unit has cooled, remove the lid. |
2. | Press down and at the same time turn the pressure regulator knob |
| counterclockwise past the STEAM setting and carefully lift to remove. Look |
| through the holes to make sure there is no particle build up, and put it under |
3. | running water. |
Turn the lid over an d place on a ta ble top. Pull out the | |
| Using a brush or toothpick, check and remove any food or foreign particles |
| that may be lodged in the floating valve. Replace the |
4. | pressing down. |
Replace the pr essure regulator knob by lining the two notches up to the | |
| inside wall of the pressure regulator chamber in the lid and turning clock- |
| wise. The white button on the lid should line up with the pressure or steam |
| setting on the pressure regulator knob. If it doesn’t, remove the knob again |
| and try realigning the notches the other way around. |
ENGLISH
|
|
|
16 | 17 | |
|
|
|