| Page 10 of 24 |
4.4.Client Side Map Descriptors
4.4.1.FieldServer Related Map Descriptor Parameters
| Column Title |
|
| Function |
|
|
|
| Legal Values | ||
| Map_Descriptor_Name |
| Name | of | this | Map |
| Up | to | 32 | alphanumeric |
|
| Descriptor |
|
|
| characters |
| ||||
|
|
|
|
|
|
| |||||
|
|
| Name | of | Data | Array |
| One of the Data Array | |||
| Data_Array_Name |
| where data is to be |
| |||||||
|
| stored |
| in | the |
| names | from | “Data Array” | ||
|
|
| FieldServer |
|
|
| section above |
| |||
|
|
|
|
|
|
|
|
|
| ||
| Data_Array_Offset |
| Starting location in Data |
| 0 to | maximum specified in | |||||
|
| Array |
|
|
|
| “Data Array” section above | ||||
|
|
|
|
|
|
| |||||
| Function |
| Function of Client Map |
| Server, Passive_Client | ||||||
|
|
| Descriptor. |
|
|
|
|
|
|
| |
4.4.2.Driver Related Map Descriptor Parameters
| Column Title |
| Function |
| Legal Values | |
|
|
|
|
| One of | the node |
| Node_Name | Name of Node to fetch data from |
| names | specified | |
|
|
|
|
| in Section 4.3 | |
|
|
| This driver uses this parameter to determine |
|
|
|
|
|
| the suitability of a Map Descriptor when |
|
|
|
|
|
| looking for a location to store data from an |
|
|
|
|
|
| incoming message. |
|
|
|
| Event Type |
| A Map Descriptor may be defined to store |
| Any, Other, Fault, | |
|
|
| Alarm, Trouble | |||
|
|
| only ‘Alarm’, ‘Fault’, ‘Trouble’ or ‘Other events. |
|
|
|
|
|
| Alternatively, specify “Any” |
|
|
|
|
|
| A table of events vs. categories is provided in |
|
|
|
|
|
| Appendix A.1 |
|
|
|
|
|
| This driver uses this parameter to determine |
| Zone, | Relay, |
|
|
| the suitability of a Map Descriptor when |
| ||
| Point Type |
| looking for a location to store data from an |
| Loop, | Sensor, |
|
|
| incoming message. |
| Module, Panel | |
|
|
|
|
|
| |
|
|
| Ignored when the Point Type is ‘Panel’ |
|
|
|
| Relay/Loop/Zone |
| Point Type = Relay 1..255 |
| Whole Numbers | |
|
| Point Type = Zone 1..8 |
| |||
| Number |
| Point Type = Loop 1..2 |
| 1, 2 , etc |
|
|
|
| Point Type = Module 1..2 |
|
|
|
|
|
| Point Type = Sensor 1..2 |
|
|
|
|
|
| Each Map Descriptor defines storage |
| 1,2,3 .etc | |
| Length |
| locations for a series of addresses. This |
| Whole numbers | |
|
|
| parameter specifies the length of the series. |
|
|
|
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408)
