Manuals / Fisher & Paykel / Kitchen Appliance / Dishwasher

Fisher & Paykel DD90SDFTM2 7a CAVITY PREPARATION, Water Connection, Water Pressure, Benchtop

Models: DD90SDF(H)TX2 DD90SDFTM2

1 24

Download 24 pages 46.48 Kb

Page 10

Image 10

7a CAVITY PREPARATION

10 mm

BENCHTOP

2 mm

Moisture protection tape must be applied.

Important!

The power outlet must be located in a cabinet adjacent to the dishwasher cavity.

220-240 VAC min. 7 A

Water Connection

Recommended COLD (Maximum 60°C).

These marks indicate formed bracket screw locations, if securing by drawer removal.

Important!

Adjacent cabinetry must not extend above cavity base

Services can be located either side of the dishwasher.

min. ø 60 mm

¾ “ BSP (GB20) to suit flat washer.

Water Pressure

Water softener models

Max. 1 MPa (145 psi)

Min. 0.1 MPa (14.5 psi)

Models without water softener

Max. 1 MPa (145 psi)

Min. 0.03 MPa (4.3 psi)

min. 200 mm

Page 10

Image 10

Fisher & Paykel DD90SDFTM2 manual 7a CAVITY PREPARATION, Water Connection, Water Pressure, Water softener models, Benchtop

Contents

NZ AU GB IE INSTALLATION INSTRUCTIONSDishDrawerTM dishwasher DD90SDFHTX2, DD90SDFTM2 Designer DD90SHTI2 Integrated modelsDD90STI2 1 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODELDD90SDFHTX2 DD90SDFTM2 DD90SHTI2IMPORTANT SAFETY INSTRUCTIONS 2a SAFETY AND WARNINGS - ALL MODELS2b ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY IMPORTANT SAFETY INSTRUCTIONSDrain hose 3a PARTS SUPPLIED - ALL MODELSWire clip Drain hosePanel bracket 3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELSExternal Venting kit attached to productProduct dimensions mm 4 PRODUCT DIMENSIONSPlan Side 5 CABINETRY DIMENSIONSCabinetry dimensions mm PlanWIDTH OF THE PANEL FRONT PANEL SPECIFICATIONSmin. 2mm ventilation gap with external venting kit installed HEIGHT OF THE PANELHEIGHT OF THE PANEL FRONT PANEL SPECIFICATIONSWIDTH OF THE PANEL min. 2mmWater Connection 7a CAVITY PREPARATIONServices can be located either side of the dishwasher Water PressureShelf cutouts Shelf cutoutsPower cord excl. plug - 400 mm 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGEPower cord excl. plug - 750 mm Venting hose - 1265 mm Left hand sidePage 10a INTEGRATED MODELS WITH REMOTE NZ AU ONLY 9a ATTACH SIDE MOUNTING BRACKETSATTACH VENTING HOSE NOW CHOOSE WHICH INSTALLATION METHOD a or bEnsure correct chassis position. In order 11a PULL THROUGH HOSES & MOVE INTO THE CAVITY12a SECURE THE DRAWER for product to function, cabinetry mustALTERNATIVE METHOD b - SECURE BY DRAWER REMOVAL 9b INTEGRATED MODELS WITH REMOTE NZ AU ONLY ATTACH VENTING HOSE10b PULL THROUGH HOSES & MOVE INTO THE CAVITY Fitted Elbow13b REFIT THE DRAWER ONTO THE RUNNERS 11b REMOVE THE DRAWER12b SECURE THE DRAWER TO THE CABINETRY SECURE THE EXTERNAL VENT16a ATTACH PANEL TO PANEL BRACKET INTEGRATED MODELS WITH REMOTE NZ AU ONLY - INSTALLING THE FRONT PANEL15a REMOVE BRACKET FROM PRODUCT Use all 14 screws provided as shownINTEGRATED MODELS WITH REMOTE NZ AU ONLY - INSTALLING THE FRONT PANEL 17a EARTH THE PANEL18a ATTACH PANEL TO PRODUCT When refitting the door pins, ensure they are orientated as shown16b REMOVE BRACKET & DISCONNECT BADGE 17b ROUTE BADGE WIRING THROUGH PANEL15b DETERMINE BADGE CUTOUT LOCATION 18b ATTACH PANEL TO PANEL BRACKETWhen refitting the 19b REATTACH BADGE & EARTH THE PANEL20b ATTACH PANEL TO PRODUCT door pins, ensure they are orientated as shownRepeat on the other side if necessary 21 ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPSIntegrated models with remote control The panel has a maximum travel of 2 mm up or downDishwasher and Standpipe Ø 38 mm 23 CONNECT INLET HOSE TO COLD WATER 24 PLUG PRODUCT INDishwasher using sink trap with drain hose joiner 750-882.5 mmNo program indicator lights up when the drawer is opened 25 FINAL CHECKLIST26 TROUBLESHOOTING SAVE THESE INSTRUCTIONS