Manuals / Fisher & Paykel / Kitchen Appliance / Dishwasher

Fisher & Paykel DD90SDF(H)TX2, DD90SDFTM2 17a EARTH THE PANEL, 18a ATTACH PANEL TO PRODUCT, place

Models: DD90SDF(H)TX2 DD90SDFTM2

1 24

Page 19

INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - INSTALLING THE FRONT PANEL		19
17a EARTH THE PANEL	18a ATTACH PANEL TO PRODUCT

WARNING!

Electrical Shock Hazard

To earth the panel bracket, connect the earth wire from the product to one of the tabs. Any custom metal component (e.g. handle) that extends past the rubber seal must be earthed too.

Failure to follow these warnings may result in electrical shock, injury or fire.

	Important!
	Ensure the rubber seal
	between the drawer
2	and panel is kept in
	place.

When refitting the door pins, ensure they are orientated as shown.

Page 19

Image 19

Fisher & Paykel DD90SDF(H)TX2, DD90SDFTM2 manual 17a EARTH THE PANEL, 18a ATTACH PANEL TO PRODUCT, place

Contents

DD90SDFHTX2, DD90SDFTM2 Designer DD90SHTI2 Integrated models INSTALLATION INSTRUCTIONSDishDrawerTM dishwasher NZ AU GB IEDD90SHTI2 1 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODELDD90SDFHTX2 DD90SDFTM2 DD90STI2IMPORTANT SAFETY INSTRUCTIONS 2a SAFETY AND WARNINGS - ALL MODELS2b ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY IMPORTANT SAFETY INSTRUCTIONSDrain hose 3a PARTS SUPPLIED - ALL MODELSWire clip Drain hoseattached to product 3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELSExternal Venting kit Panel bracketProduct dimensions mm 4 PRODUCT DIMENSIONSPlan Plan 5 CABINETRY DIMENSIONSCabinetry dimensions mm SideHEIGHT OF THE PANEL FRONT PANEL SPECIFICATIONSmin. 2mm ventilation gap with external venting kit installed WIDTH OF THE PANELmin. 2mm FRONT PANEL SPECIFICATIONSWIDTH OF THE PANEL HEIGHT OF THE PANELWater Pressure 7a CAVITY PREPARATIONServices can be located either side of the dishwasher Water ConnectionShelf cutouts Shelf cutoutsLeft hand side 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGEPower cord excl. plug - 750 mm Venting hose - 1265 mm Power cord excl. plug - 400 mmPage NOW CHOOSE WHICH INSTALLATION METHOD a or b 9a ATTACH SIDE MOUNTING BRACKETSATTACH VENTING HOSE 10a INTEGRATED MODELS WITH REMOTE NZ AU ONLYfor product to function, cabinetry must 11a PULL THROUGH HOSES & MOVE INTO THE CAVITY12a SECURE THE DRAWER Ensure correct chassis position. In orderFitted Elbow 9b INTEGRATED MODELS WITH REMOTE NZ AU ONLY ATTACH VENTING HOSE10b PULL THROUGH HOSES & MOVE INTO THE CAVITY ALTERNATIVE METHOD b - SECURE BY DRAWER REMOVALSECURE THE EXTERNAL VENT 11b REMOVE THE DRAWER12b SECURE THE DRAWER TO THE CABINETRY 13b REFIT THE DRAWER ONTO THE RUNNERSUse all 14 screws provided as shown INTEGRATED MODELS WITH REMOTE NZ AU ONLY - INSTALLING THE FRONT PANEL15a REMOVE BRACKET FROM PRODUCT 16a ATTACH PANEL TO PANEL BRACKETWhen refitting the door pins, ensure they are orientated as shown 17a EARTH THE PANEL18a ATTACH PANEL TO PRODUCT INTEGRATED MODELS WITH REMOTE NZ AU ONLY - INSTALLING THE FRONT PANEL18b ATTACH PANEL TO PANEL BRACKET 17b ROUTE BADGE WIRING THROUGH PANEL15b DETERMINE BADGE CUTOUT LOCATION 16b REMOVE BRACKET & DISCONNECT BADGEdoor pins, ensure they are orientated as shown 19b REATTACH BADGE & EARTH THE PANEL20b ATTACH PANEL TO PRODUCT When refitting theThe panel has a maximum travel of 2 mm up or down 21 ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPSIntegrated models with remote control Repeat on the other side if necessary750-882.5 mm 23 CONNECT INLET HOSE TO COLD WATER 24 PLUG PRODUCT INDishwasher using sink trap with drain hose joiner Dishwasher and Standpipe Ø 38 mmSAVE THESE INSTRUCTIONS 25 FINAL CHECKLIST26 TROUBLESHOOTING No program indicator lights up when the drawer is opened

17a EARTH THE PANEL

18a ATTACH PANEL TO PRODUCT

place.

When refitting the door pins, ensure they are orientated as shown.