Manuals / Fisher & Paykel / Kitchen Appliance / Dishwasher

Fisher & Paykel DD90SDF(H)TX2 3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS, Panel bracket

Models: DD90SDF(H)TX2 DD90SDFTM2

1 24

Page 5

3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS

3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS	5

External Venting kit (1)	Panel bracket (1)	Panel mounting
	(attached to product)	screws (14)

supplied with Integrated models with remote (NZ AU) only

Integrated rectangular badge (1) (Satin chrome supplied)

supplied with Integrated models with badge (GB IE) only

Page 5

Image 5

Fisher & Paykel DD90SDF(H)TX2 3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS, External Venting kit, Panel bracket

Contents

DishDrawerTM dishwasher INSTALLATION INSTRUCTIONSNZ AU GB IE DD90SDFHTX2, DD90SDFTM2 Designer DD90SHTI2 Integrated modelsDD90SDFHTX2 DD90SDFTM2 1 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODELDD90STI2 DD90SHTI22b ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY 2a SAFETY AND WARNINGS - ALL MODELSIMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONSWire clip 3a PARTS SUPPLIED - ALL MODELSDrain hose Drain hoseExternal Venting kit 3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELSPanel bracket attached to productPlan 4 PRODUCT DIMENSIONSProduct dimensions mm Cabinetry dimensions mm 5 CABINETRY DIMENSIONSSide Planmin. 2mm ventilation gap with external venting kit installed FRONT PANEL SPECIFICATIONSWIDTH OF THE PANEL HEIGHT OF THE PANELWIDTH OF THE PANEL FRONT PANEL SPECIFICATIONSHEIGHT OF THE PANEL min. 2mmServices can be located either side of the dishwasher 7a CAVITY PREPARATIONWater Connection Water PressureShelf cutouts Shelf cutoutsPower cord excl. plug - 750 mm Venting hose - 1265 mm 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGEPower cord excl. plug - 400 mm Left hand sidePage ATTACH VENTING HOSE 9a ATTACH SIDE MOUNTING BRACKETS10a INTEGRATED MODELS WITH REMOTE NZ AU ONLY NOW CHOOSE WHICH INSTALLATION METHOD a or b12a SECURE THE DRAWER 11a PULL THROUGH HOSES & MOVE INTO THE CAVITYEnsure correct chassis position. In order for product to function, cabinetry must10b PULL THROUGH HOSES & MOVE INTO THE CAVITY 9b INTEGRATED MODELS WITH REMOTE NZ AU ONLY ATTACH VENTING HOSEALTERNATIVE METHOD b - SECURE BY DRAWER REMOVAL Fitted Elbow12b SECURE THE DRAWER TO THE CABINETRY 11b REMOVE THE DRAWER13b REFIT THE DRAWER ONTO THE RUNNERS SECURE THE EXTERNAL VENT15a REMOVE BRACKET FROM PRODUCT INTEGRATED MODELS WITH REMOTE NZ AU ONLY - INSTALLING THE FRONT PANEL16a ATTACH PANEL TO PANEL BRACKET Use all 14 screws provided as shown18a ATTACH PANEL TO PRODUCT 17a EARTH THE PANELINTEGRATED MODELS WITH REMOTE NZ AU ONLY - INSTALLING THE FRONT PANEL When refitting the door pins, ensure they are orientated as shown15b DETERMINE BADGE CUTOUT LOCATION 17b ROUTE BADGE WIRING THROUGH PANEL16b REMOVE BRACKET & DISCONNECT BADGE 18b ATTACH PANEL TO PANEL BRACKET20b ATTACH PANEL TO PRODUCT 19b REATTACH BADGE & EARTH THE PANELWhen refitting the door pins, ensure they are orientated as shownIntegrated models with remote control 21 ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPSRepeat on the other side if necessary The panel has a maximum travel of 2 mm up or downDishwasher using sink trap with drain hose joiner 23 CONNECT INLET HOSE TO COLD WATER 24 PLUG PRODUCT INDishwasher and Standpipe Ø 38 mm 750-882.5 mm26 TROUBLESHOOTING 25 FINAL CHECKLISTNo program indicator lights up when the drawer is opened SAVE THESE INSTRUCTIONS

3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS

External Venting kit (1)

Panel bracket (1)

(attached to product)

supplied with Integrated models with remote (NZ AU) only

Integrated rectangular badge (1) (Satin chrome supplied)

supplied with Integrated models with badge (GB IE) only