Model
Applying a compressor/limiter to the mic input during overdubbing!
Using the
The INSERT jack accepts a TRS (tip, ring, sleeve) 1/4" connector for
Microphone
MIC IN 2/4
|
| 1/3 | MIC IN |
| 2/4 |
|
| L/MONO | R | L | R | L |
| R |
|
|
|
| |
|
|
|
|
|
|
| AUX SEND | AUX RTN | MONITOR OUT | LINE OUT |
|
|
|
| |||||
| TRIM 1/3 |
|
|
| TRIM 2/4 |
|
|
|
|
|
|
|
|
|
|
|
| WIDE PITCH | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| + 6 |
|
|
|
| 6 + |
|
|
EQ HI | 0 |
| 0 |
| 0 |
| 0 | AUX RTN |
|
|
| 3 |
|
|
|
| 3 | – | + |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| 0 |
|
|
|
| 0 | NORMAL | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
- + | - + | - + | - + |
|
|
|
| 5 |
|
|
|
| 5 | FIX |
| ||||
0 | 10 |
|
| - 10 |
|
|
|
| 10 - |
|
| ||||||||
EQ LO | 0 |
| 0 |
| 0 |
| 0 | MONITOR |
|
|
| L | R | 1 | 2 | 3 | 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| NR |
|
| REC |
| POWER |
|
|
- | + | - | + | - | + | - | + | 0 | 10 |
|
|
|
|
|
| RESET |
|
|
|
MON MIX/ |
|
|
|
|
|
|
| AUX |
|
|
|
|
|
|
|
|
|
|
|
AUX |
|
|
|
|
|
|
|
|
|
|
|
|
| 0 0 0 |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
0 | 10 | 0 | 10 | 0 | 10 | 0 | 10 | MON MIX |
|
|
|
|
|
|
|
|
|
| |
PAN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Track |
|
|
|
|
|
|
|
|
|
| |
L | R | L | R | L | R | L | R | Down |
|
|
|
|
|
|
|
|
|
| |
| 1 |
| 2 |
| 3 |
| 4 |
|
|
|
|
|
|
|
|
|
|
|
|
4 | REC TRK | 4 | REC TRK | 4 | REC TRK | 4 |
| REC TRK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
3 |
| 3 |
| 3 |
| 3 |
| Auto |
|
|
|
|
|
|
|
|
|
| |
2 |
| 2 |
| 2 |
| 2 |
| Bounce |
|
|
|
|
|
|
|
|
|
| |
1 |
| 1 |
| 1 |
| 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| DOLBY B NR |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| REC | PLAY |
| REW | FF | STOP | PAUSE |
|
| 1 |
| 2 |
| 3 |
| 4 | MASTER |
|
|
|
|
|
|
|
|
|
| |
|
|
| LINE IN/INSERT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
LINE IN/INSERT 4
Tip (Return)
Ring (Send)
Compressor/limiter
In this example, a microphone is plugged into the MIC IN jack 2/4 and a vocal is recorded to track 4.
1.Connect the microphone to one of the MIC IN jacks 2/4 (1/4” or XLR) on the rear panel of the
2.Connect the input/output of the compressor/ limiter to the insert jack 4 as shown in the drawing.
3.Press the REC TRK switch on channel 4 once to select track 4 as the recording track.
4.While talking into the microphone, adjust the recording level using the Trim 2/4 knob until segments 0 - 3 on the level meter light up.
5.Adjust the effect signal on the compressor/ limiter.
Refer to the manual for the compressor/limiter for detailed effect settings.
6.Follow the instructions on page 16 for overdubbing.
In this way, you can apply the compressor/limiter to only the vocal recorded to track 4.
26
