FujiFilm FinePix S9100, S9600 Warning Displays

Warning Displays				eThe table below lists the warnings that are displayed on the screen.
Warning Displayed			Explanation		Remedy
		(Lit red)	The camera	batteries are low or	Load new or fully charged batteries.
		(Blinking red)	completely out of charge.
			There is a strong likelihood of camera		Use flash photography. However, use a tripod for
			shake because the shutter speed is slow.		some scenes and modes.
			The AF (autofocus) cannot work effectively.		i If the image is too dark, take the picture at a
					distance of around 2 m (6.6 ft.) from the subject.
					i Use AF lock to take the picture.
					i Select Macro mode when taking close-up shots.
Aperture/Shutter speed display			Outside the AE continuous range.		The picture can be taken, but the correct
	(Lit red)				brightness (exposure) will not be obtained.
FOCUS ERROR			Camera malfunction or fault.		i Turn the camera on again, taking care not to
					touch the lens.
ZOOM ERROR					i Turn the camera off and on again. If the
					message still appears, contact your FUJIFILM
					dealer.
NO CARD			No media is inserted.		Insert a media.
			i The media is not formatted.		i Format the media on the camera.
			i The xD-Picture Card contact area is		i Wipe the contact area on the xD-Picture Card
CARD NOT INITIALIZED			soiled.		with a soft dry cloth. It may be necessary to
					format the xD-Picture Card. If the message still
					appears, replace the xD-Picture Card.
			i Camera fault.		i Contact your FUJIFILM dealer.
			i The xD-Picture Card contact area is		i Wipe the contact area on the xD-Picture Card
CARD ERROR			soiled.		with a soft dry cloth. It may be necessary to
			i The media format is incorrect.		format the xD-Picture Card. If the message still
			i Camera fault.		appears, replace the xD-Picture Card.
			i The media is damaged.		i Contact your FUJIFILM dealer.
CARD FULL			The media is full.		Erase some images or use a media that has
					ample free space.
			i The data could not be recorded due to a		i Re-insert the media or turn the camera off and
			media error or a connection error		then on again. If the message still appears,
			between the media and camera.		contact your FUJIFILM dealer.
WRITE ERROR			i The image cannot be recorded as it is		i Use a new media.
			too large to fit in the available space on
			the media.		i Format the xD-Picture Card on the camera
			i The xD-Picture Card is not formatted.
					(➡P.104).
		BUSY	The timing for recording was incorrect		Use a media that was formatted on the camera.
			because the media was formatted on a PC.
			The frame number has reached 999-9999.		1 Insert a formatted media into the camera.
					2 Set “RENEW” as the FRAME NO. setting in
FRAME NO. FULL					the “SET-UP” menu.
					3 Start taking pictures (The frame number starts
					from “100-0001”).
					4 Set “CONT.” as the FRAME NO. setting in the
					“SET-UP” menu.
			i The played back file was not recorded		i Images cannot be played back.
			correctly.
			i The xD-Picture Card contact area is		i Wipe the contact area on the xD-Picture Card
			soiled.		with a soft dry cloth. It may be necessary to
READ ERROR					format the xD-Picture Card. If the message still
					appears, replace the xD-Picture Card.
			i Camera fault.		i Contact your FUJIFILM dealer.
			i An attempt was made to play a movie or		i Movies and images cannot be played back.
			display an image that was not recorded
			on this camera.
TOO MANY FRAMES			An attempt was made to show 5,000 or		No more than 4,999 images can be shown by
			more images by date sorting.		date sorting.

Warning Displayed	Explanation	Remedy
	i A protected file was encountered.	i Protected files cannot be erased. Remove the
		protection.
PROTECTED FRAME	i An attempt was made to add a voice	i Protected files cannot be added to voice
	memo to protected file.	memos. Remove the protection.
	i An attempt was made to rotate a	i Protected files cannot be rotated. Remove the
	protected file.	protection.
t ERROR	i The voice memo file is faulty.	i The voice memo cannot be played back.
	i Camera fault.	i Contact your FUJIFILM dealer.
` CAN NOT TRIM	An attempt was made to trim a 0.3M image	The image cannot be trimmed.
	or an image shot with the RAW setting.
~ CAN NOT TRIM
	i An attempt was made to trim an image	The image cannot be trimmed.
CAN NOT TRIM	shot using a camera other than FinePix
	S9100 / FinePix S9600.
	i The image is damaged.
	Prints were specified for 1000 or more	The maximum number of frames for which prints
DPOF FILE ERROR	frames in the DPOF frame settings.	can be specified on the same media is 999.
		Copy the images for which you want to order
		prints onto another media and then specify the
		DPOF settings.
CAN NOT SET DPOF	An attempt was made to specify DPOF	DPOF printing cannot be used with this image
~ CAN NOT SET DPOF	settings for an image that is not supported	format.
r CAN NOT SET DPOF	by DPOF.
r CAN NOT ROTATE	An attempt was made to rotate a movie.	These images cannot be rotated by image
		formats.
COMMUNICATION	The camera is not connected to a PC or	i Check that the USB cable (mini-B) is connected
	printer.	correctly.
ERROR
		i Check that your printer is turned on.
	Displayed for PictBridge.	i Check that the printer is not out of paper or out
		of ink.
PRINTER ERROR		i Turn the printer off briefly and then turn it back
		on.
		i Refer to the user manual supplied with your
		printer.
	Displayed for PictBridge.	Check that the printer is not out of paper or out of
PRINTER ERROR		ink. Printing automatically restarts when the error
		is cleared. If the message still appears after
RESUME?
		checking, press the “MENU/OK” button to restart
		printing.
	Displayed for PictBridge.	i Refer to the user manual for the printer being
		used and check whether the printer supports the
		JFIF-JPEG or Exif-JPEG image format. If not,
		the printer cannot print the images.
CANNOT BE PRINTED		i Movies and images with CCD-RAW cannot be
		printed.
		i Was the image data photographed using
		FinePix S9100 / FinePix S9600?
		You may not be able to print some images
		photographed on other cameras.
	Displayed for PictBridge.	This message appears when printing is performed
u PRINTING		from a FUJIFILM printer that supports PictBridge.
		Refer to the Owner’s Manual for the printer for
		details.

142 143