Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MAG3182FC Sense data, the command termination status. This information is transferred to

Models: MAG3182FC MAF3364FC MAG3091FC

1 107

Download 107 pages 9.99 Kb

Page 101

Sense data:	Detailed information created by the target when any error is involved in
	the command termination status. This information is transferred to
	report the error.
Sense key:	Four-bit code added to the sense data to identify the class of detected
	error.
Status:	One byte of information that is transferred from a target to an initiator on
	termination of each command to indicate the command termination
	status.
Target:	SCSI device which performs I/O initiated by an initiator. It is abbreviated
	as TARG.

GL - 2

C141-E078-02EN

Image 101

Fujitsu MAG3182FC Sense data, the command termination status. This information is transferred to, report the error, Status

Contents

FIBRE CHANNEL INTERFACE PRODUCT MANUAL C141-E078-02ENMAF3364FC SERIES MAG3182FC, MAG3091FC SERIES DISK DRIVES Revised contents REVISION RECORDSpecification No. C141-E078-**EN The contents of this manual is subject to change without prior noticeThis page is intentionally left blank Functional Limitations FOR SAFE OPERATIONHandling of This manual Related Standards Chapter 4 INSTALLATION REQUIREMENTS Chapter 2 SPECIFICATIONSChapter 5 INSTALLATION Chapter 6 DIAGNOSIS and MAINTENANCEDANGER CONVENTIONSModel names DISCLAIMERList of Important Precautions SAFETY PRECAUTIONSWhen the SEND DIAGNOSTIC command terminates with the CHECK PrecautionCONDITION status, the INIT must collect the error information using the REQUEST SENSE command. The RECEIVE DIAGNOSTIC1. General Description 2. Specifications 3. Data Format This manual FIBRE CHANNEL INTERFACE SPECIFICATIONS4. Installation Requirements 5. Installation 6. Diagnostics and Maintenance 1. Fibre Channel InterfaceSPECIFICATIONS CONTENTSINSTALLATION REQUIREMENTS CHAPTERCHAPTER 6 DIAGNOSTICS AND MAINTENANCE CHAPTER 5 INSTALLATIONAPPENDIX A LOCATIONS OF CONNECTORS APPENDIX B CONNECTOR SIGNAL ALLOCATIONGL-1 GlossaryAbbreviations AB-1FIGURES TABLES This page is intentionally left blank CHAPTER 1 GENERAL DESCRIPTION 1.1 Standard Features 1.2 Hardware Structure 1.3 System Configuration1.1 Standard Features 9 Command queuing feature 8 Read-ahead cache feature11 Enclosure service function 12 Error recovery14 Programmable data block length 20 Low power consumption15 Defective block slipping 16 High speed positioningC141-E078-02EN 1.2 Hardware StructureFigure 1.1 MAF3364FC outer view Figure 1.2 MAG series outer view Disk/head configuration 5 Air circulation recirculation filter, breather filter 4 Actuator6 Read/write circuit 7 Controller circuitFigure 1.4 FC-AL system configuration 1.3 System Configuration2.1 Hardware Specifications 2.1.1 Model name and part number CHAPTER 2 SPECIFICATIONS2.1 Hardware Specifications Function specifications 2.1.2 Function specificationsMAG3364FC Seek Time MAG series Seek Time 5 This value indicates at ready modeC141-E078-02EN Environmental/power requirements 2.1.3 Environmental specifications5 to 50C 5 to 55C2.1.5 Reliability 2.1.4 Error rateStrengthen cooling power so that DE 3 Service life4 Data security at power failure 2 Mean Time To Repair MTTRCHAPTER 3 DATA FORMAT 3.1.1 Cylinder configuration3.1 Data Space 3.2 Logical Data Block Addressing 3.3 Defect ManagementP MAF3364FC = 10400 MAG series = Figure 3.1 Cylinder configurationZone layout and track capacity MAG series Zone layout and track capacity MAF3364FC3.1.2 Alternate spare area SPR1 Figure 3.2 Spare area in cylindersFigure 3.3 Alternate cylinder 3.1.3 Track format 119,700 CLKs*120MHz Figure 3.4 Track formatSector format Figure 3.5 Track skew/cylinder skew3.1.4 Sector format 2 PLO Sync Each sector on the track consists of the following fields 1 Gaps G13 Trailing TRNG/Sync Byte SB 4 LBA The logical block address is written in this field 5 Data fieldTable 3.3 Format capacity 3.1.5 Format capacity3.2 Logical Data Block Addressing 3.3.2 Alternate block allocation 3.3 Defect Management 3.3.1 Defect listC141-E078-02EN 1 Alternate block allocation during FORMAT UNIT command executionFigure 3.7 Alternate block allocation by FORMAT UNIT command Figure 3.8 Alternate block allocation by REASSIGN BLOCKS command Automatic alternate block allocation is made only once during the execution of one command. If second defective block is detected, the alternate block assignment processing for the first defective block is executed but the alternate block assignment processing for the second one is not executed and the command being executed terminates. However, the initiator can recover the twice error by issuing the same command again This page is intentionally left blank 4.1 Mounting Requirements 4.2 Power Supply Requirements CHAPTER 4 INSTALLATION REQUIREMENTS4.1 Mounting Requirements 4.1.1 External dimensions 4.3 Connection RequirementsC141-E078-02EN Figure 4.1 External dimensions MAF3364FCC141-E078-02EN Figure 4.2 External dimensions MAG seriesFigure 4.3 IDD orientation 4.1.3 Notes on mounting 4.1.2 MountingFigure 4.4 Mounting frame structure Figure 4.5 Limitation of side-mounting Figure 4.6 Surface temperature measurement points Surface temperature check pointFigure 4.7 Service clearance area a MAF3364FC Air pressure adjustment hole b MAG series Figure 4.8 Air pressure adjustment holeAir pressure adjustment hole C141-E078-02ENFigure 4.9 Current waveform +12 VDC 4.2 Power Supply RequirementsFigure 4.10 AC noise filter recommended 4.3 Connection Requirements 4.3.1 ConnectorFigure 4.11 Connector location of SCA2 type interface model 4.3.3 Recommended components for connection 4.3.2 Interface connectorFigure 4.12 SCA2 type interface connector 5.1 Notes on Handling Drives 5.2 Setting 5.3 Mounting Drives CHAPTER 5 INSTALLATION5.4 Confirming Operations after Installation and Preparation for Use 5.5 Dismounting Drive4 Packaging 3 Installation5 Delivery 6 Storage a Provide vaporproof packaging for storageTable 5.1 Motor start mode 5.2 Setting 5.2.1 Loop ID setting5.2.2 Mode settings 5.3 Mounting Drives 5.3.1 Mounting procedures 5.4 Confirming Operations after Installation and Preparation for Use 5.4.1 Confirming initial operationsRemark 5.4.2 Checking connection C141-E078-02N Figure 5.1 Checking the IDD connection AMotor starts when power is turned on For Figure Motor starts by START/STOP command Executing time opprox. 30 seconds Figure 5.2 Checking the IDD connection BTo Figure C141-E078-02EN5.4.3 Formatting 5.4.4 Setting parameters 1. At factory shipment of the IDD, the saving operation for the MODE SELECT parameter is not executed. So, if the user does not set parameters, the IDD operates according to the default value of each parameter ∙ ARRE ∙ TB ∙ PER ∙ Time required for reconnection processing Specifying the multipliers of minimum prefetch queued commandabsolute value 0 After releaseC141-E078-02EN 5.5 Dismounting DriveThis page is intentionally left blank 6.1 Diagnostics 6.2 Maintenance Information CHAPTER 6 DIAGNOSTICS AND MAINTENANCE6.1 Diagnostics 6.1.1 Self-diagnostics Table 6.1 Self-diagnostic functions1 Initial self-diagnostics Brief test contents of self-diagnostics are as followsa. Hardware function test ∙ RAM microcode is stored ∙ Peripheral circuits of microprocessor MPUa. Error recovery during self-diagnostics 2 Online self-diagnostics SEND DIAGNOSTIC commandOperation of self-diagnostics b. Reporting result of self-diagnostics and error indicationData loss 6.1.2 Test programs6.2 Maintenance Information 6.2.1 Maintenance requirements 3 Parts that can be replaced in the field Figure 6.1 Revision label 6.2.2 Revision numbersFigure 6.2 Indicating revision numbers A.1 Locations of Connectors APPENDIX A LOCATIONS OF CONNECTORSA.1 Locations of Connectors Figure A.1 Locations of connectorsRear view MAF3364FC Rear view MAG series C141-E078-02ENB.1 Interface FC-SCA Connector Signal Allocation APPENDIX B CONNECTOR SIGNAL ALLOCATIONTable B.1 FC-SCA connector CN1 Interface FC-SCA Connector Signal AllocationC.1 Model Names and Product Numbers APPENDIX C MODEL NAMES AND PRODUCT NUMBERSTable C.1 MAF and MAG series model names and product numbers Model Names and Product Numbersstorage typeAPPENDIX D FIBRE CHANNEL INTERFACE FUNCTIONS D.1 Fibre Channel Interface Function SpecificationsTable D.1 Fibre channel interface function specifications Fibre Channel Interface Function Specifications1 of Table D.1 Fibre channel interface function specifications2 of Table D.1 Fibre channel interface function specifications3 of 4 of Table D.1 Fibre channel interface function specifications5 of 6 of 7 of 8 of This page is intentionally left blank Glossary report the error the command termination status. This information is transferred toerror termination of each command to indicate the command terminationAbbreviations Page This page is intentionally left blank Page