Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MAG3091FC manual Installation, Notes on Handling Drives 5.2 Setting 5.3 Mounting Drives

Models: MAG3182FC MAF3364FC MAG3091FC

1 107

Download 107 pages 9.99 Kb

Page 60

CHAPTER 5 INSTALLATION

CHAPTER 5 INSTALLATION

5.1Notes on Handling Drives

5.2Setting

5.3Mounting Drives

5.4Confirming Operations after Installation and Preparation for Use

5.5Dismounting Drive

This chapter describes the notes on handling drives, connections, setting switches and plugs, mounting drives, connecting cables, confirming drive operations after installation and preparation for use, and dismounting drives.

5.1Notes on Handling Drives

(1)General notes

a)Do not give the drive shocks or vibrations exceeding the value defined in the standard because it may cause critical damage to the drive. Especially be careful when unpacking.

b)Do not leave the drive in a dirty or contaminated environment.

c)Since static discharge may destroy the CMOS semiconductors in the drive, note the following after unpacking:

∙Use an antistatic mat and body grounding when handling the drive.

∙Hold the DE when handling the drive. Do not touch PCAs except for setting.

(2)Unpackaging

a)Use a flat work area. Check that the "This Side Up" sign side is up. Handle the package on soft material such as a rubber mat, not on hard material such as a desk.

b)Be careful not to give excess pressure to the internal unit when removing cushions.

c)Be careful not to give excess pressure to the PCAs and interface connector when removing the drive from the antistatic bag.

d)Do not remove the sealing label or cover of the DE and screws.

C141-E078-02EN

5 - 1

Image 60

Fujitsu MAG3091FC, MAF3364FC Installation, Notes on Handling Drives 5.2 Setting 5.3 Mounting Drives, Dismounting Drive

Contents

C141-E078-02EN MAF3364FC SERIES MAG3182FC, MAG3091FC SERIES DISK DRIVESFIBRE CHANNEL INTERFACE PRODUCT MANUAL REVISION RECORD Revised contentsSpecification No. C141-E078-**EN The contents of this manual is subject to change without prior noticeThis page is intentionally left blank FOR SAFE OPERATION Handling of This manualFunctional Limitations Related Standards Chapter 2 SPECIFICATIONS Chapter 4 INSTALLATION REQUIREMENTSChapter 5 INSTALLATION Chapter 6 DIAGNOSIS and MAINTENANCECONVENTIONS DANGERDISCLAIMER Model namesSAFETY PRECAUTIONS List of Important PrecautionsPrecaution When the SEND DIAGNOSTIC command terminates with the CHECKCONDITION status, the INIT must collect the error information using the REQUEST SENSE command. The RECEIVE DIAGNOSTICThis manual FIBRE CHANNEL INTERFACE SPECIFICATIONS 1. General Description 2. Specifications 3. Data Format4. Installation Requirements 5. Installation 6. Diagnostics and Maintenance 1. Fibre Channel InterfaceCONTENTS SPECIFICATIONSINSTALLATION REQUIREMENTS CHAPTERCHAPTER 5 INSTALLATION CHAPTER 6 DIAGNOSTICS AND MAINTENANCEAPPENDIX A LOCATIONS OF CONNECTORS APPENDIX B CONNECTOR SIGNAL ALLOCATIONGlossary GL-1Abbreviations AB-1FIGURES TABLES This page is intentionally left blank 1.1 Standard Features 1.2 Hardware Structure 1.3 System Configuration CHAPTER 1 GENERAL DESCRIPTION1.1 Standard Features 8 Read-ahead cache feature 9 Command queuing feature11 Enclosure service function 12 Error recovery20 Low power consumption 14 Programmable data block length15 Defective block slipping 16 High speed positioning1.2 Hardware Structure Figure 1.1 MAF3364FC outer view Figure 1.2 MAG series outer viewC141-E078-02EN Disk/head configuration 4 Actuator 5 Air circulation recirculation filter, breather filter6 Read/write circuit 7 Controller circuit1.3 System Configuration Figure 1.4 FC-AL system configurationCHAPTER 2 SPECIFICATIONS 2.1 Hardware Specifications2.1 Hardware Specifications 2.1.1 Model name and part number 2.1.2 Function specifications Function specifications5 This value indicates at ready mode C141-E078-02ENMAG3364FC Seek Time MAG series Seek Time 2.1.3 Environmental specifications Environmental/power requirements5 to 50C 5 to 55C2.1.4 Error rate 2.1.5 Reliability3 Service life ∙ DE surface temperature ∙ DE surface temperature∙ DE surface temperature ∙ DE surface temperature ∙ DE surface temperature3.1.1 Cylinder configuration CHAPTER 3 DATA FORMAT3.1 Data Space 3.2 Logical Data Block Addressing 3.3 Defect ManagementFigure 3.1 Cylinder configuration P MAF3364FC = 10400 MAG series =Zone layout and track capacity MAF3364FC Zone layout and track capacity MAG series3.1.2 Alternate spare area Figure 3.2 Spare area in cylinders Figure 3.3 Alternate cylinder 3.1.3 Track formatSPR1 Figure 3.4 Track format 119,700 CLKs*120MHzFigure 3.5 Track skew/cylinder skew 3.1.4 Sector formatSector format Each sector on the track consists of the following fields 1 Gaps G1 2 PLO Sync3 Trailing TRNG/Sync Byte SB 4 LBA The logical block address is written in this field 5 Data field3.1.5 Format capacity Table 3.3 Format capacity3.2 Logical Data Block Addressing 3.3 Defect Management 3.3.1 Defect list 3.3.2 Alternate block allocation1 Alternate block allocation during FORMAT UNIT command execution C141-E078-02ENFigure 3.7 Alternate block allocation by FORMAT UNIT command Figure 3.8 Alternate block allocation by REASSIGN BLOCKS command Automatic alternate block allocation is made only once during the execution of one command. If second defective block is detected, the alternate block assignment processing for the first defective block is executed but the alternate block assignment processing for the second one is not executed and the command being executed terminates. However, the initiator can recover the twice error by issuing the same command again This page is intentionally left blank CHAPTER 4 INSTALLATION REQUIREMENTS 4.1 Mounting Requirements 4.2 Power Supply Requirements4.1 Mounting Requirements 4.1.1 External dimensions 4.3 Connection RequirementsFigure 4.1 External dimensions MAF3364FC C141-E078-02ENFigure 4.2 External dimensions MAG series C141-E078-02EN4.1.2 Mounting Figure 4.3 IDD orientation 4.1.3 Notes on mountingFigure 4.4 Mounting frame structure Figure 4.5 Limitation of side-mounting Surface temperature check point Figure 4.6 Surface temperature measurement pointsFigure 4.7 Service clearance area Figure 4.8 Air pressure adjustment hole a MAF3364FC Air pressure adjustment hole b MAG seriesAir pressure adjustment hole C141-E078-02EN4.2 Power Supply Requirements Figure 4.9 Current waveform +12 VDC4.3.1 Connector Figure 4.11 Connector location of SCA2 type interface modelFigure 4.10 AC noise filter recommended 4.3 Connection Requirements 4.3.2 Interface connector Figure 4.12 SCA2 type interface connector4.3.3 Recommended components for connection CHAPTER 5 INSTALLATION 5.1 Notes on Handling Drives 5.2 Setting 5.3 Mounting Drives5.4 Confirming Operations after Installation and Preparation for Use 5.5 Dismounting Drive3 Installation c To prevent condensation, avoid sudden changes in temperature4 Packaging 5 Delivery5.2 Setting 5.2.1 Loop ID setting 5.2.2 Mode settingsTable 5.1 Motor start mode 5.3 Mounting Drives 5.3.1 Mounting procedures 5.4.1 Confirming initial operations Remark5.4 Confirming Operations after Installation and Preparation for Use 5.4.2 Checking connection Figure 5.1 Checking the IDD connection A Motor starts when power is turned on For FigureC141-E078-02N Figure 5.2 Checking the IDD connection B Motor starts by START/STOP command Executing time opprox. 30 secondsTo Figure C141-E078-02EN5.4.3 Formatting 5.4.4 Setting parameters 1. At factory shipment of the IDD, the saving operation for the MODE SELECT parameter is not executed. So, if the user does not set parameters, the IDD operates according to the default value of each parameter ∙ ARRE ∙ TB ∙ PER ∙ Time required for reconnection processing queued command Specifying the multipliers of minimum prefetchabsolute value 0 After release5.5 Dismounting Drive C141-E078-02ENThis page is intentionally left blank CHAPTER 6 DIAGNOSTICS AND MAINTENANCE 6.1 Diagnostics 6.2 Maintenance Information6.1 Diagnostics 6.1.1 Self-diagnostics Table 6.1 Self-diagnostic functionsBrief test contents of self-diagnostics are as follows 1 Initial self-diagnosticsa. Hardware function test ∙ RAM microcode is stored ∙ Peripheral circuits of microprocessor MPU2 Online self-diagnostics SEND DIAGNOSTIC command a. Error recovery during self-diagnosticsOperation of self-diagnostics b. Reporting result of self-diagnostics and error indication6.1.2 Test programs Data loss6.2 Maintenance Information 6.2.1 Maintenance requirements 3 Parts that can be replaced in the field 6.2.2 Revision numbers Figure 6.1 Revision labelFigure 6.2 Indicating revision numbers APPENDIX A LOCATIONS OF CONNECTORS A.1 Locations of ConnectorsFigure A.1 Locations of connectors A.1 Locations of ConnectorsRear view MAF3364FC Rear view MAG series C141-E078-02ENAPPENDIX B CONNECTOR SIGNAL ALLOCATION B.1 Interface FC-SCA Connector Signal AllocationInterface FC-SCA Connector Signal Allocation Table B.1 FC-SCA connector CN1APPENDIX C MODEL NAMES AND PRODUCT NUMBERS C.1 Model Names and Product NumbersModel Names and Product Numbers Table C.1 MAF and MAG series model names and product numbersstorage typeD.1 Fibre Channel Interface Function Specifications APPENDIX D FIBRE CHANNEL INTERFACE FUNCTIONSFibre Channel Interface Function Specifications 1 ofTable D.1 Fibre channel interface function specifications Table D.1 Fibre channel interface function specifications2 of Table D.1 Fibre channel interface function specifications3 of 4 of Table D.1 Fibre channel interface function specifications5 of 6 of 7 of 8 of This page is intentionally left blank Glossary the command termination status. This information is transferred to report the errorerror termination of each command to indicate the command terminationAbbreviations Page This page is intentionally left blank Page