Display unit, inside view | Furuno FR-2115/2125 manual

	A
A	Pass cable
	through here.

J475

J474

J473

Cable Tie CV-100, 2 pcs.

Pan-head Screw M3X8, 4 pcs.

J451

INT Board 03P9252

J471

Existing cable tie

J472

NH Connector

03-1991(3P), 4 pcs.

ALARM Board 03P9262

NH Connector 03-1990(9-9P)

Pan-head screw M4X12

Cable Band

HP-3N

Figure 4-16 Display unit, inside view

HOW TO INSULATE THE POWER CABLE

Shrink Tubing

					Solder

		20 mm
1 Make length of					2 Solder power	3 Heat shrink
shrink tubing 20 mm;					cable to signal cable.	tubing with solder-
slip tubing onto wiring.						ing iron.

4-16

Image 55

Furuno FR-2115/2125 manual Display unit, inside view

Contents

Marine Radar B . N o . I M E 3 4 6 4 0 M Safety Instructions Power Switch Power Switch in AC Powered Display Unit Table of Contents Standard Supply Equipment Lists Name Type Code No Qty Remarks Optional Equipment System Configuration Mounting considerations Scanner Unit Assembling the scanner unit Be sure to remove the guide pins Fastening the radiator to the radiator bracket Fastening the scanner unit to the mounting platform Scanner unit, front view Tabletop mounting Mounting procedureDisplay Unit Before mounting the display unit Stay Setting catch to hole in stay Console type mounting 11 How to dismount the PTU cover Separating the control head Display unit modification procedureSeparate type control head kit Type OP03-151, No 13 Detaching the control head Control head modification procedure Connection of display unit to control head Plate Attachment of hood 15 How to attach KB fixing plate Wiring Scanner unit, front view, cover removed Correct seating of waterproofing gasket Fabricating signal cable S03-75 =EMI cores Outer cores RFC-13 thick Inner cores RFC-10 thin Fabricating signal cable S03-74 DPYCY-3.5 Fabricating the AC power cable supplied CVV-S 82C Fabricating the DC power cable CVV-S 8 x 2C, option Leading in cables to the display unit Cable fed from rear of display unit Default Cables fed from bottom of display unit for console mount Cable fed from outside display unit M4X8 2 pcs Connections Connectors on the INT Board Connectors on the INT Board How to attach NH connector Changing AC Power Specification Restoring default settings Tuning InitializationAccessing Menus for Initialization and Adjustment Adjusting Video Signal Level Picture appears Deviated counterclockwise Heading Alignment Suppressing Main Bang Adjusting Sweep Timing Magnetron heater voltage rating Confirming Magnetron Heater Voltage Press Radar Menu 0 0 0 Initial Setting Menus Initial SETTING2 menu Initial SETTING1 menuInitial SETTING3 menu OWN Ship Information menu Initial SETTING4 menu Gyro Converter GC-8 Installation and connection of the Gyro Converter Board Gyro Converter Board 64P1106 DIP switch, jumper wire settings Connection of external power supplyDefault setting Gyrocompass type Frequency Setting method 1 by gyrocompass specifications JP1 JP2 JP3 JP4 JP5 Setting method 2 by make and model of gyrocompass SW1 Setting the heading readout on the radar display ARP Board ARP-26 Installation of the ARP board ARP Board 18P9002B ARP board adjustment ARP Board ARP-26 Final check Table top/console type RP Board RP-26 10 Display pedestal Necessary parts RP-26-Z-2E Code no Separate type control head 13 Display pedestal, front view Necessary parts PM-30 and OP03-150 Code no Performance Monitor PM-30 Procedure Alarm KitNecessary parts OP03-156 Code no 16 Display unit, inside view AC-DC Conversion Kit Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page