Gyro Converter Board 64P1106 | Furuno FR-2115/2125 instruction

4)Connect the GYRO CONVERTER Board to the INT Board (cables supplied with GC-8) as shown below.

J5

To gyro

J4

J446 J7

J1

J465

Fix cable to chassis

INT BOARDwith cable tie. 03P9252

GYRO CONVERTER BOARD 64P1106

Figure 4-2 Display unit, inside view

5)Confirm gyrocompass specifications and set up the DIP switches and jumper wires on the GYRO CONVERTER Board according to gyrocompass connected:

•Setting jumper wires and DIP switches by gyrocompass specifications: page 4-3

• Setting jumper wires and DIP switches by make and model of gyrocompass: page 4-5

•Location of jumper wires and DIP switches: page 4-6

6)Solder the gyrocompass cable to the VH connector assemblies (supplied).

7)Attach instruction label (supplied) to the shield cover for the INT and GYRO CONVERTER boards.

8)Close the display unit.

9)Turn the power off and on to reset the CPU.

4-2

Image 41

Furuno FR-2115/2125 manual Gyro Converter Board 64P1106

Contents

Marine Radar B . N o . I M E 3 4 6 4 0 M Safety Instructions Power Switch Power Switch in AC Powered Display Unit Table of Contents Standard Supply Equipment Lists Name Type Code No Qty Remarks Optional Equipment System Configuration Mounting considerations Scanner Unit Assembling the scanner unit Be sure to remove the guide pins Fastening the radiator to the radiator bracket Fastening the scanner unit to the mounting platform Scanner unit, front view Display Unit Mounting procedureBefore mounting the display unit Tabletop mounting Stay Setting catch to hole in stay Console type mounting 11 How to dismount the PTU cover Separate type control head kit Type OP03-151, No Display unit modification procedureSeparating the control head 13 Detaching the control head Control head modification procedure Connection of display unit to control head Plate Attachment of hood 15 How to attach KB fixing plate Wiring Scanner unit, front view, cover removed Correct seating of waterproofing gasket Fabricating signal cable S03-75 =EMI cores Outer cores RFC-13 thick Inner cores RFC-10 thin Fabricating signal cable S03-74 DPYCY-3.5 Fabricating the AC power cable supplied CVV-S 82C Fabricating the DC power cable CVV-S 8 x 2C, option Leading in cables to the display unit Cable fed from rear of display unit Default Cables fed from bottom of display unit for console mount Cable fed from outside display unit M4X8 2 pcs Connections Connectors on the INT Board Connectors on the INT Board How to attach NH connector Changing AC Power Specification Accessing Menus for Initialization and Adjustment Tuning InitializationAdjusting Video Signal Level Restoring default settings Picture appears Deviated counterclockwise Heading Alignment Suppressing Main Bang Adjusting Sweep Timing Magnetron heater voltage rating Confirming Magnetron Heater Voltage Press Radar Menu 0 0 0 Initial Setting Menus Initial SETTING3 menu Initial SETTING1 menuInitial SETTING2 menu OWN Ship Information menu Initial SETTING4 menu Gyro Converter GC-8 Installation and connection of the Gyro Converter Board Gyro Converter Board 64P1106 Default setting Connection of external power supplyDIP switch, jumper wire settings Gyrocompass type Frequency Setting method 1 by gyrocompass specifications JP1 JP2 JP3 JP4 JP5 Setting method 2 by make and model of gyrocompass SW1 Setting the heading readout on the radar display ARP Board ARP-26 Installation of the ARP board ARP Board 18P9002B ARP board adjustment ARP Board ARP-26 Final check Table top/console type RP Board RP-26 10 Display pedestal Necessary parts RP-26-Z-2E Code no Separate type control head 13 Display pedestal, front view Necessary parts PM-30 and OP03-150 Code no Performance Monitor PM-30 Necessary parts OP03-156 Code no Alarm KitProcedure 16 Display unit, inside view AC-DC Conversion Kit Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page