Furuno GP-1610CF H

A-4

Icons

LL

• Unsuitable chart/chart card not inserted.

• Chart scale/range is too small. (Page 4-4)

• Suitable chart scale is selected.

(Page 4-4)

• Chart position is offset. (Page 10-3)

• Battery voltage (on pcb) is low.

(Page 14-1)

• Chart scale/range is too large.

• Chart data is unreliable. (Page 4-4)

• L/L position is offset.

(Page 10-1)

• Alarm setting violated.

• Disappears when reason for alarm is

cleared. (Page 3-7—3-8, 9-1—9-2)

• Track is not being recorded.

(Page 5-1)

Contents

Main PUB. No. OME-43861 FIRST EDITION : MAR. 1997 G : MAR. 7, 2001 SAFETY INSTRUCTIONS Safety Instructions for the Operator About the TFT LCD WARNING CAUTION CAUTION WARNING FOREWORD INSTALLATION OPERATIONAL OVERVIEW TABLE OF CONTENTS BY SUBJECT GPS, CHART OVERVIEW TRACK MARKS Page iii TABLE OF CONTENTS BY DISPLAY ITEM H CSE 350.0 SPD 16.8kt 2D DEP 110 m TMP 16.0C 13:42 POS 3426.345N 13541.232E BRG+ 232.0 RNG+ 0.00nm 2D DEP 110 m FOREWORD A Word to GP-1610CF Owners Features System Configuration 1-1 INSTALLATION 1.1 Equipment Lists Standard supply .oNemaNepyT.oNedoCytQskrameR 1tinUyalpsiD E-FC0161-PG 1 2tinUannetnA 610-APG 1 3 noitallatsnI slairetaM 00300-68PC830-140-000tes1 4straPerapS 00300-68PS 046-493-400tes1 Optional equipment (con't) 1.2 Installation of Standard Equipment Installing the display unit Installing the antenna unit Page Page Page Wiring CAUTION Figure 1-11 Display unit, rear view 1-9 1.3 Installation of Transducers Installing the inside-hull mount transducer Page 3.9 Page Installing the thru-hull mount transducer Page Page Installing the transom mount transducer Transducer preparation 1.4 Installation of Optional Sensors Through-hull mount water temperature/speed sensor (ST-02MSB, ST-02PSB) Transom mount water temperature sensor T-02MTB Thru-hull mount water temperature sensor T-03MSB 1-21 Figure 1-28 Thru-hull mount water temperature sensor T-03MSB 1.5 Connection of Optional Equipment Figure 1-29 Connection of the FURUNO GR-80 DGPS receiver Connecting a DGPS beacon receiver 1-22 Figure 1-30 Connection of other DGPS beacon receivers Connecting a sensor MJ-A6SRMD MJ-A10SRMD MJ-A10SPF Figure 1-31 Wiring of converter connector for water temperature sensor Figure 1-32 Wiring of converter connector for water temperature/speed sensor To connector at rear of display unit MJ-A10SPF MJ-A6SRMD MJ-A10SRMD Water temp., water temp/speed sensor connector Transducer connector Figure 1-33 Connection of transducer, water temperature sensor, water temperature/speed sensor 1.6 Initial Settings Sensor connection Autopilot or remote display connection Page DGPS beacon receiver connection 2-1 OPERATIONAL OVER VIEW 2.1 Control Description Figure 2-1 Controls 2.2 Inserting Chart Cards 2.3 Turning On/Off the Power 2.4 Adjusting Tone and Brilliance 2.5 Plotter Displays 34 26.345' N 13538.417' E 127.1 16.8 15.2 110 248 323 2.6 Sounder Displays Page 2.7 Basic Menu Operation 3.1 Principle of Operation VIDEO SOUNDER OPERATION 3.2 Automatic Sounder Operation 3.3 Manual Sounder Operation 3.4 Suppressing Low Level Noise 3.5 Selecting Picture Advance Speed 3.6 Suppressing Interference 3.7 Erasing Weak Echoes 3.8 Changing Zoom Magnification Factor 3.9 Selecting Hue (color arrangement) 3.10 Measuring Depth 3.11 Knowing Depth Change by Audible Chime 3.12 Selecting Unit of Depth Measurement 3.13 Offsetting the Depth Readout 3.14 Displaying the Water Temperature Graph 3.15 Selecting Unit of Water Temperature Measurement 3.16 Offsetting Water Temperature Readout 3.17 Fish Alarm 3.18 Bottom Alarm 3.19 Water Temperature Alarm 3.20 Turning On/Off the Expansion Range Marker 3.21 Receiver Sensitivity (gain) Adjustment 3.22 Selecting Bottom-Lock Expansion Width 3.23 Stopping Transmission 3.24 Interpreting the Display Page GPS, CHART OVERVIEW 4.1 Principle of GPS Page 4.2 Presentation Mode 4.3 Shifting the Cursor 4.4 Selecting Screen Center by Cursor 4.5 Shifting the Display 4.6 Centering Position 4.7 Changing Chart Scale/ Range 4.8 Chart Cards Page FL(2) G 12S 15M 5.1 Stopping/Restarting Plotting of Track TRACK 5.2 Changing Track Color 5.3 Erasing All Track 5.4 Changing Track Plotting Interval 5.5 Smoothing Track MARKS 6.1 Entering Marks 6.2 Entering Event Marks 6.3 Erasing Individual Marks 6.4 Changing Mark Attributes 6.5 Entering the MOB Mark 6.6 Erasing All Marks 6.7 Radar Target Mark WAYPOINTS, ROUTES 7.1 Entering Waypoints Page 7.2 Erasing Individual Waypoints 7.3 Changing Waypoint Position 7.4 Changing Waypoint Mark Size 7.5 Entering Routes 7.6 Editing Routes 7.7 Erasing Routes SETTING DESTINATION 8.1 Setting Destination Page 8.2 Skipping Route Waypoints 8.3 Cancelling Destination PLOTTER-RELATED ALARMS 9.1 Arrival/Anchor Watch Alarm 9.2 XTE (Cross Track Error) Alarm 9.3 Speed Alarm 9.4 Trip Alarm POSITION-RELATED OPERATIONS 10.1 Displaying Position in LOPs 10.2 Offsetting GPS Position 10.3 Selecting Navaid 10.4 Displaying True or Magnetic Bearings 10.5 Magnetic Variation 10.6 Offsetting Chart Position GPS OPERATIONS 11.1 GPS Setup Menu 11.2 Speed Averaging OPTIONAL EQUIPMENT SETUP 12.1 Selecting Sensors 12.2 Selecting Autopilot, Remote Display 12.3 Setting up DGPS Beacon Receiver 12-2 CUSTOMIZING THE DISPLA Y 13.1 Plotter Display Marker Attributes 13.2 Chart Attributes 13.3 Unit of Distance Measurement 13.4 Chart Range or Scale Indication MAINTENANCE & TROUBLESHOOTING 14.1 Maintenance WARNING 14.2 Replacement of Fuse, Battery 14.3 Simple Troubleshooting Table 14-2 Simple troubleshooting (con't) 14.4 Error Messages 14.5 Diagnostic Tests 14.6 GPS Monitor Display 14.7 Demonstration Display 14.8 Memory Card Operations (for technicians) 14.9 Clearing the Memory Specifications Video Sounder GPS Receiver Plotter Section I/O Data Format Page A-3 Geodetic Chart List A-4 Icons H LL Glossary GPS Plotter Page Video Sounder Page A-9 Menu Tree A-10 A-11 A-12 Decca Chains Page Page Page Page Page Index-1 INDEX A B C D Index-2 G H I L Index-3 R S T W