GarrettCom 6K32T PoE LEDs Summary, 48VDC power in not, internally connected and, LEDs are ON

Models: 6K32T 6K32TRC

1 78
Download 78 pages 49.11 Kb
Page 66
Image 66
48VDC power in not

Magnum 6K32T & 6K32TRC Managed Switch

Installation and User Guide 05/07)

Inside) option in one 6K-unit. In this Fig. the top 4-RJ45 ports are enhanced with POE option whereas as bottom 4- RJ-45 are normal MDIX ports. The 4-RJ45 POE module are also available with mix –n-match with fiber modules. Please check the ordering information Sec.1.2. for all the various PI6K PoE modules option.

The LEDs on 6KP8-RJ45- PoE module are slightly different compared to regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the PoE LED is ON when connected properly to a 803.af compliant PD device on that port. When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by PoE.

LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK/ACT, as shown in the diagram.

PI6KP8V-45RJ

8 Port@ 10/100Mb POE Copper ports

 

1

3

 

5

 

10/10

 

 

 

LK/ACT

 

0

 

 

 

 

 

F/

2

4

6

PO

 

H

E

 

 

8

 

 

10/10

 

 

LK/ACT

 

0

 

 

 

 

4

F/H

 

 

 

PO

 

 

 

 

E

 

1

LK/ACT

2

10/100

3

PoE

4

FULL/HALF

2

internally connected andno power is coming tothe PoE ports for somereason, all the PoE port 1

3

PoE LEDs Summary

For PoE devices, each RJ-45 PoE port supports only 802.3af complaint devices. The PoE LED is ON when the attached PD is drawing power from the port.

For non-PoE devices connected, the PoE port will act as a normal RJ-45 port and the PoE LED is OFF. No power is being sent out from the port.

The PoE ports in Magnum 6K’s with 48VDC power input act as a pass- through, so the 48VDC power source must be strong enough to provide power to the 6K switch and to all the 8 RJ-45 ports with PD devices connected (up to 15 watts per PoE port).

In the case where the

48VDC power in not

 

6KP86KP8V- -45-2MT

 

internally connected and

6 Port@10/10Mbps

and 2 port @100Mb

 

no power is coming to

Multi-Mode Fiber port

 

 

the PoE ports for some

 

 

2

 

 

 

reason, all the PoE port

 

1

3

5

 

1

LEDs are ON

 

 

 

10/10

 

 

L

 

simultaneously to

4

 

 

 

 

 

indicate a trouble

F/H

 

 

AC

 

 

 

 

 

 

 

10/100

 

 

ACT

 

condition. The ports will

 

 

 

F/H

 

 

 

 

 

 

 

 

 

 

ACT

 

 

 

 

LK

F/H

 

still operate properly for

 

F/H 2

4

3

 

6

 

 

 

 

 

data traffic.

1

LINK

 

2

10/100

 

 

 

 

 

3

ACTIVITY

4

FULL/HALF

 

www . GarrettCom . com

61

Page 66
Image 66
GarrettCom 6K32T PoE LEDs Summary, 48VDC power in not, internally connected and, no power is coming to, LEDs are ON