Removing PM Cards | GarrettCom Magnum 700X manual

PM Card

PM Cards

Magnum 700X

Magnum 700X Mini-Concentrator

Magnum 700X Mini-Concentrators	Installation and User Guide (05/98)

Slowly and firmly push the PM into position. Once inserted, secure the PM card using the two screws on the front panel of the unit. Once all PM cards needed have been installed (including face plates for empty slots), replace the chassis cover.

NOTE: All PM slots need not be filled in order for the unit to be operational. When leaving PM slots empty, always use a face plate (Magnum PM-FP) to cover the opening in the front panel to keep the unit clean, and for safety.

3.5Removing PM Cards

To properly remove a PM card from the Magnum 700X Mini-Concentrator, follow the steps below.

1.Removing 700X Chassis Cover and PM Retaining Screws

Follow the procedure described for Face Plates in Section 3.3, Steps 1 and 2, above.

2.Removing PM Card

Gently pull the PM card up and out of the connector socket. If the slot from which the PM card has been removed is to remain open be sure to install an PM face plate. If another PM card is replacing the one that

has been removed, follow the steps as described for installing an PM

card discussed on the preceding pages.

NOTE: Use a face plate (Magnum PM-FP) to cover the opening in the front panel if you are leaving any 700X Mini-Concentrator slots empty.

Magnum 700X

Magnum 700X Mini-Concentrator

GARRETT

25

Image 30

GarrettCom manual Removing PM Cards, Magnum 700X Mini-Concentrator

Contents

Magnum 700X Mini-Concentrator Magnum Mini-Concentrator Installation and User Guide Trademarks Phone 510 Contacting Garrett Communications Table of Contents Introduction Magnum  Specifications Warranty Technical Specifications, ConnectorsLED Indicators on Chassis Packaging Specifications Repeater Port Modules RPMs Specifications Bridge Port Modules BPMs Ordering Information Magnum 700X Mini-Concentrator Introduction Inspecting the Package and ProductProduct Description Magnum 700X Chassis 1 Magnum 700X Mini-Concentrator Magnum 700X Repeater Port Modules RPMs RPM-DTE, RPM-FST, RPM-FSC, RPM-TP, & PM-FPRPM-BNC Magnum RPM-BNC RPM-AUI 2 AUI Pin Assignments Pin Function RPM-FST Fiber ST, Twist-lock Connector RPM-DTEMagnum RPM-FST Jumper Across Distances Supported RPM-FSC Fiber SC, Snap-in ConnectorConnector Magnum RPM-FSC RPM-SMF Single-mode Fiber 3 km Not used 10 km Magnum RPM-TP Proper cooling air flow, and for safety Magnum PM-FPRPM-TP Twisted Pair PM-FPPage BPM-AUI BPM-FSTMagnum BPM-FST Module is designed with internal Wiring STP of 150m 500 ft.. ThisBPM-TP Transceiver functionality. The Link RPMs Repeater Port Modules for All Standard Ethernet Media Front Mounted Connectors and LEDsInternal Universal Power Supply with Auto-ranging Optional Bridge Port Modules BPMs Applications Ieee Standard Reference Max. Distance Taps PM Type Media Ieee Standard Connector PM type InstallationConnecting Ethernet Media Locating Magnum 700X Mini-Concentrators Connecting ThinNet 10BASE2 BNC Connecting ThickNet 10BASE5 AUIConnecting Drop Cable 10BASE5 DTE Connecting Fiber Optic SC-type, Snap-in Connecting Single-Mode Fiber Optic SMF Connecting Twisted Pair RJ-45, Unshielded or Shielded Removing the PM Face Plate Power Supply Connector socket slot Installing PM CardsInstalling the PM Card Align the connector Pins on the PM card Removing PM Cards Operation Repeater FunctionalityBPM Local Bridge Functionality 2c and 4.2d respectively. When an Cases where an internal packet is filteredWhen the packet’s source is external, it Written there. This happens when a 2d External Packet Filtered Powering the Magnum 700X Mini-Concentrator 12.2e Local Isolation with Bridge Port Module Chassis LEDs Magnum 700X chassis unit LEDsPM LEDs Troubleshooting Before Calling for Assistance When Calling for Assistance Return Material Authorization RMA Procedure No Problem Found Shipping and Packaging Information Appendix a Warranty Information