GBC 3064WF | Operation Manual |
SEQUENCE OF OPERATIONS
GBC U.S &CE 3064WF
Effect of Fiber Optics on sequence of operation
Modes | Situation 1 | Situation 2 | Situation 3 | |
Machine Run Mode | Normal operation | Interrupted fiber optic | Fiber optic beam cleared + all safety | |
| (No Interruption to any | beam or opened any | circuitries are closed | |
| safety circuitry & Fiber | safety circuitry. |
| |
| optic beam)High speed. |
|
| |
|
|
|
| |
| Control panel: | Machine stops Instantly. | Machine will remain stationary until | |
| Forward Speed: Zero to | Use foot pedal to override | run switch is pressed. | |
| Max. | @ 3f/m. | Push RUN button switch to run | |
| Press “RUN” push |
| machine again (Normal operation) | |
| button to switch over |
| mode. | |
| from foot switch to the |
|
| |
| control panel. |
|
| |
|
|
|
| |
| Foot switch: | Machine Runs @ | Machine still remains at low voltage | |
| Forward Speed: Zero to | 3f/m. | speed of 3f/m. | |
Forward Mode | Max. | (Automatic override from | Steps required to run at (various | |
Note: Press variable | high to low voltage) | speed): The operator will have two | ||
Press push button | ||||
foot pedal to change |
| choices, | ||
forward switch |
| |||
mode and take over |
|
| ||
|
| Choice A: | ||
| from control panel at |
| ||
| preset speed. |
| 1. Release foot pedal to stop machine. | |
|
|
| 2. Press foot pedal again to start | |
|
|
| machine at original preset control | |
|
|
| panel knob speed (pot). | |
|
|
| Choice B: | |
|
|
| 1. Press and hold “RUN” push button | |
|
|
| switch on the control panel while foot | |
|
|
| is still on pedal. | |
|
|
| 2. Release foot pedal. | |
|
|
| 3. Adjust speed using “speed knob” | |
|
|
|
| |
| Reverse speed: Zero to | Machine stops Instantly. | Machine must not run. It will remain | |
| Max. | Use Foot pedal to | stationary. | |
| Press “Run” push | override @ 3f/m. | Push RUN button switch to run | |
| button to switch over |
| machine again at Normal operation | |
| from Foot switch to the |
| mode. | |
| Control panel. |
|
| |
Reverse Mode | Reverse speed: Zero to | Machine Runs @ 3f/m. | Machine still remains at low voltage | |
Max. | (Automatic override from | speed of 3f/m. | ||
Press Reverse | Note: Press foot pedal | high to low voltage) | Steps required to run at (various | |
Push button switch. | to change mode and |
| speed): The operator will have two | |
| take over from control |
| choices, | |
| panel. |
| Choice A: | |
|
|
| ||
|
|
| 1. Release foot pedal to stop machine. | |
|
|
| 2. Press foot pedal again to start | |
|
|
| machine at original preset control | |
|
|
| panel knob speed (pot). | |
|
|
| Choice B: | |
|
|
| 1. Press and hold “RUN” push button | |
|
|
| switch on the control panel while foot | |
|
|
| is still on pedal. | |
|
|
| 2. Release foot pedal. | |
|
|
| 3. Adjust speed using “speed knob” | |
|
|
|
|
© 2005 General Binding Corporation | Page 14 |